Home Forums Product Discussion & Questions BeoGram Beogram 4500 (and others) main pcb question

Viewing 8 posts - 1 through 8 (of 8 total)
  • Author
    Posts
  • #60033
    Jonathan McCall
    BRONZE Member

      Idiot question I’m afraid.

      How do I get this ribbon cable off ? The connector has a top clip which come off, however I’m not sure whether I should be giving it some welly to try and get it off after loosening the clip, or de-soldering the whole connector from the pcb.

      Thanks

      Jonny

      Attachments:
      You must be logged in to view attached files.
      #60037
      Madskp
      GOLD Member
        • Denmark

        I don’t know if it is the case here, but on some B&O systems the plastic parts i not a connector, but more a kind of strain relief for the cable. In that case you will have to unsolder. Not easy to see if that is the case here

        #60038
        Jonathan McCall
        BRONZE Member

          Thanks Mad – I’m thinking that’s the case here, as a firm pull doesn’t give any success. There is a YouTube video of Kose Trading just pulling the cable out on a Beogram 3000, but I’d prefer to take the educated route before getting ham fisted.

          If anyone else can chip in that would be appreciated.

          #60053
          Guy
          Moderator
            • Warwickshire, UK

            Clutching at straws but the service manual shows P6 as being a ‘socket 6-pins’ and in the exploded parts diagram PCB1 is shown with just the socket in place (no attached plug or wire showing).

            The ‘plug’ would then be part of the connector from the muting module (module 11).

            I think it should come apart.  (It’s possibly a old Molex right angle PCB connector – something like this:  https://www.molex.com/en-us/products/part-detail/09481064 )

            IMPORTANT EDIT:  But the service manual does cover a variety of Beogram models so there may have been variations of connector – like in the BG3000 video that you mentioned.  Also, if you look at Condor Audio’s BG4500 restoration, the cable appears to be soldered directly to the board, perhaps another variation or a modification (possibly after breaking the previously connector – so be careful!!)  Condor Audio BG4500 pdf here (perhaps @yachadm of Condor Audio can comment):  https://www.condoraudio.com/wp-content/uploads/Projects/BeoGram-4500-Turntable-Restoration-Repair.pdf

            EDIT 2:  This advert appears to show your BG4500 board with the connector disconnected:  https://kosetrading.com/product/beogram-4500-computer-control-circuit-part-pcb-1/

            #60057
            Jonathan McCall
            BRONZE Member

              Really helpful – thanks Guy. I’m using a component kit from Condor to recap the PSU board, main board and RIAA as well as new diodes, a couple of op-amps (SMD so will leave those to an expert) and new 33&45 trimmers.

              I know it sounds like a know what I’m talking about, but I’m basically learning as I go along and it’s very interesting and fun following the circuit diagram and finding out what everything does.

              Ive dropped Menahem an email on the connector, so hopefully he can help.

              Cheers

              Jonny

              #60058
              Jonathan McCall
              BRONZE Member

                The Kose board with just the connector shown was I think the same one from the video where the cable just pulled straight out.

                Tried doing that again and no joy, so going with a de-solder. At least that will give me the opportunity to see how it all goes together.

                The clip on top of the connector also appears to have little prongs to separate the cables as they enter the connector.

                #60060
                Dillen
                Moderator

                  It was not meant to be disconnected.
                  I always desolder the connector from the board.

                  Martin

                  #60145
                  Jonathan McCall
                  BRONZE Member

                    Putting everything back together, although still awaiting the RIAA back from my expert in SMDs.

                    Out of curiosity, can anyone enlighten me as to what the mica plate is for under the PSU board ? It appears to be a shield for the component that sits on top of it, to stop dust getting in, but allowing someone me form of cooling ?

                    I may be totally wrong, but always keen to learn.

                    Incidentally, that spring clip is a b ugger to get back on !

                    Cheers

                    Jonny

                     

                    Attachments:
                    You must be logged in to view attached files.
                  Viewing 8 posts - 1 through 8 (of 8 total)
                  • You must be logged in to reply to this topic.