Posts by kumse (archived)
28 total posts21 results
MX8000.. got the 5 digit manufacturer code, what now?
in The Workbench · Dec 25, 2011 16:21Blacktrix Can you tell me how i activate a new four digit pincode now i have entered the master code? Kindly Regards Thomas
MX8000.. got the 5 digit manufacturer code, what now?
in The Workbench · Dec 24, 2011 17:55Thank you Blackrix ! It worked! Happy holidays to you!
MX8000.. got the 5 digit manufacturer code, what now?
in The Workbench · Dec 24, 2011 11:44Hello out there Bought a second hand MX8000 and had it stored for a while. i forgot the code and contacted b&o, they gave me a five digit code, and told me to follow the user guide. The user guide says that i have to loo…
BeoCenter AV5 CD mechanism in BeoCenter 3000 ??
in The Workbench · Oct 30, 2011 12:10Hi Blackrix Do you know where i can find a servicemanual for the AV5 to check? Thomas
BeoCenter AV5 CD mechanism in BeoCenter 3000 ??
in The Workbench · Oct 29, 2011 16:05Hello out there To make a long story short.. i have a BeoCenter 3000 with a faulty cd mechanism. It seems like the servo IC's are making a lot of trouble. I have used a lot of time on troubleshooting it. I have a hard ti…
Periodic faulty CD on Beosound 3000....
in The Workbench · Feb 23, 2011 18:25Well I have done some control measurements. Controlling the supply voltages for the circuits on the CD Pro2 board. They seems okay. I returned to the issue, that the spindle motor did not rotate, even that it got the ser…
Periodic faulty CD on Beosound 3000....
in The Workbench · Feb 22, 2011 18:27Hello guys After further investigation, im a bit confused. I can not find the resistor to measure the laser current 80R3121. I have tried to operate the unit in service mode. When i try to play cd, it plays nice with sou…
Periodic faulty CD on Beosound 3000....
in The Workbench · Feb 21, 2011 15:21Hello out there My lovely beosound 3000 have started doing trouble... When i try to load a cd, the clamp goes down, and opens a few seconds after. The cd does not spin. Sometimes it turns ~1mm. Sometimes it suddenly read…
Beocenter 9300 cd fault
in The Workbench · Oct 1, 2010 13:31yachadm, Die_bogener, Dillen ... >> Maybee i wasnt clear in my post, sorry guys! I read a lot of your replies at this workbench forum, i know you all are experienced, and you should know i really admire you are doing rep…
Beocenter 9300 cd fault
in The Workbench · Sept 29, 2010 10:00[quote user="Clive"] The cd doesn't spin after accepting a disk and the door then reopens. I've tried a very light clean of the laser lens to no avail. Are there any common faults or simple checks I could do with a meter…
Overture CD only responds in Testmode...
in The Workbench · Apr 10, 2010 14:02Thank you for your quick response. Have you solved a similar problem by changing caps? I suspect some µController, or other control issue, because the drive must be electrical "ok" when i can perform these test procedure…
Overture CD only responds in Testmode...
in The Workbench · Apr 10, 2010 13:30Hello out there I have an Overture Type 2623. The CD does not work in normal operation. When i select CD and press Play, the display shows "CD <>". I can hear the laser is focusing in the beginning, but the CD does not s…
MX4000 deflection connector burned....
in The Workbench · Apr 7, 2010 16:13As a follow up, i soldered the wires manually, and it have worked perfectly for month now. As a hint to the story, the lady told me that the picture tube was changed during the waranty. This seems to be an ooops made by …
Beosound Overture, No response on Tape/CD/IR...
in The Workbench · Apr 7, 2010 16:10Hello out there I just recived my new Beosound Overture Type 2623, but it does not work as it should. At the first look the CD try to focus, but does not spin up. The Tape deck try to load the tape, but does not run the …
MX4000 deflection connector burned....
in The Workbench · Dec 11, 2009 06:48Hello out there I brought a defective MX4000 MKII type 3334 from 1995. The lady i brought it from told me, that suddenly one day when she wathced television, black smoke went out of it, and she turned it off. I expected …
MX7000 with white horisontal lines in picture... (now with pics!)
in The Workbench · Nov 11, 2008 18:38ipaul>> That sounds like a smart move, to interchange the output connections to the tube. I just read your post a bit to late, because i already had done some soldering on the output board today. It actually showed sever…
MX7000 with white horisontal lines in picture... (now with pics!)
in The Workbench · Nov 11, 2008 08:40Thank you for your answer! Ipaul>> Yes i also realised that it was important to describe the error were green in stead of white :) I will start out with resolder the output board again. I will change the three output tra…
MX7000 with white horisontal lines in picture... (now with pics!)
in The Workbench · Nov 10, 2008 16:36Here you can se how the picture changes... it changes every five minutes or so. And here you can se with the green lines:
MX7000 with white horisontal lines in picture... (now with pics!)
in The Workbench · Nov 10, 2008 14:55Die_Bogener >> Thank you for your input! Im just wondering, the picture distortion is green like?? But you are right. I should try to move G2 to remove dust inside. In which area should i change caps? It will maybee be a…
MX7000 with white horisontal lines in picture... (now with pics!)
in The Workbench · Nov 10, 2008 09:29Thank you very much for your reply! I have noticed, that the color the screen lights up is slight green, and the lines are green too. Its both on television picture, and in teletext. Maybee its the green chanel in the ou…