CPADave

Forum Replies Created

Viewing 12 posts - 1 through 12 (of 12 total)
  • Author
    Posts
  • in reply to: can I fix my Beomaster 8000 #50140
    CPADave
    BRONZE Member

      I agree with Steve’s solution.  Unfortunately, I need to fix my Beomaster 8000.

      Thank you, Dave

      in reply to: can I fix my Beomaster 8000 #50137
      CPADave
      BRONZE Member

        Trackbeo wrote “wire up a headphone jack to RCAs, to see if the Beolabs are still functioning”

        Thanks, but the Beomaster8000 needs repair.

        I also have a Beomaster2400.

        1. Is the headphone jack on a Beomaster2400 the equivalent of a preamp?
        2. The BM2400 has significantly less power than my BM8000:
          1. 30W with 2 speakers or 15W with 4 speakers.
          2. Do I need to connect 4 speakers to drop the power to 15W, or,
          3. do I simply need to move the 2nd speakers switch from Off to On?
          4. Can I connect the Beolab8000 speakers directly to the 2nd speakers connection on the BM2400?
        in reply to: can I fix my Beomaster 8000 #50136
        CPADave
        BRONZE Member

          I will re-configure the entire system around a pre-amp (not yet delivered) until such time as I can get the Beomaster8000 repaired.  Until then, no receiver (radio) but some stations such as NPR are available on line.

          in reply to: can I fix my Beomaster 8000 #50135
          CPADave
          BRONZE Member

            Glitch, Sorry, but my skills are not high enough to attempt dis-assembling the Beomaster8000.

            in reply to: can I fix my Beomaster 8000 #50134
            CPADave
            BRONZE Member

              Derek, Thanks for the referrals!

              in reply to: can I fix my Beomaster 8000 #50131
              CPADave
              BRONZE Member

                Derek thanks for your suggestions!  My Beomaster 8000 is VERY heavy and I live near Portland, Oregon.  Is there a repair shop in the Pacific Northwest?

                in reply to: can I fix my Beomaster 8000 #50128
                CPADave
                BRONZE Member

                  I made custom cables: 2-pin din at the Beomaster end and RCA at the speaker end.

                  in reply to: Beogram for BeoMaster #42886
                  CPADave
                  BRONZE Member

                    Thank you!

                    in reply to: Beogram for BeoMaster #42884
                    CPADave
                    BRONZE Member
                      1. no, I don’t have a fluke VOM
                      2. no soldering experience in last 50 years
                      3. no

                      Thanks for your help!  I’ll try to find a shop in Portland.

                      in reply to: Beogram for BeoMaster #42882
                      CPADave
                      BRONZE Member

                        Hi Mark-sf

                        Do you still recommend sound-smith after the following answers?

                        1) Does the platter spin once the arm has moved towards the center?  – YES
                        2) Does the arm respond to the cueing control when it has moved inward? – NO
                        3) Does the 33 speed adjust light illuminate? -YES

                        4) the stylus needs to be re-tipped

                        5) there are NO B&O outlets in Washington or Oregon (I live 2 hours east of Portland)

                        Thanks, Dave (cpa.cowboy@yahoo.com)

                        in reply to: Beogram for BeoMaster #42880
                        CPADave
                        BRONZE Member

                          Hi Mark, If I try to play, the arms move ~1cm and then stop.  Each time I try use the switches to move towards the center of the record, the arms move ~1cm and then stop.  The arm with the cartridge never drops down.  The arms do not travel in the other direction away from the center of the record. The only way to move the arms back is to remove the covers and then turn the “screw” manually.

                          Thanks, Dave [cpa.cowboy@yahoo.com]

                          in reply to: Beogram for BeoMaster #42878
                          CPADave
                          BRONZE Member

                            I may be confused, but once-upon-a-time, I was told that various models of Beogram turntables did NOT work with each BeoMaster.  Anyway, I have a Beomaster 8000 now.

                            The 4002 turntable was purchased from Chelsea Audio in downtown Portland, Oregon, but that store doesn’t service my B&O turntable anymore.  And I can’t find a walk-in service center in Portland, Oregon.  (I live 2 hours east of Portland.)

                            1. Where can I get service for my 4002 turntable?
                            2. Can I send it directly, or must I deal with one of the sales-only B&O outlets?
                            3. Will the service center for my 4002 be the same place for getting the cartridge repaired or replaced?

                            Thanks, Dave [cpa.cowboy@yahoo.com]

                          Viewing 12 posts - 1 through 12 (of 12 total)