[Kim]

Found the issue for the above and it was issue with ML cable in my LexCom panel and once isolated and found the issue the Moment is not once again available in the ML-network.

Location: Malmo, Sweden

[Kim]

Followed the discussion, but haven’t had time to test yet as I’ve been busy pulling some CAT7 cable in the house. True the primary objective is to feed the audio from the Beosystem 6500 were the Beogram 6500 to the rest of the house which has my biggest interest, so don’t care about the Radio, CD or the cassette (well tape could be fun if it would be easy and without any conflict of commands being re-used). And as Tignum writes, I still utilise the BS6500 in the office and needs to have the speakers connected directly, and don’t care about audio from any other sources from either ML/NL devices. The office is were I tend to listen to vinyl and occasional CD’s as well and if I listen to vinyl in sometimes I finds it nice to share the analogue wealth with the rest of the household. 🙂

Location: Malmo, Sweden

[Kim]

Tignum wrote:

Do you have speakers connected to the BS6500?

Yes, do have a pair of Beovox 100 and a Cona connected to the Beomaster which is used regularly but there is no intention to pull audio from the rest of the ML, but rather as mentioned, to distribute the Beogram audio from the BS6500 to the rest of the MasterLink system.

Question, and I’m might just be overthinking this, but with the connection flow going from BS6500 -> 1611 -> BLC -> NL/LAN how does I get the jump from the BLC to the ML. I mean the 1611 is connect with ML cable to the original port in my BLC but can I also use the additional RJ45 ML port; but assume that they’re the same port but just different form factor?

Location: Malmo, Sweden

[Kim]

@Guy : No need to be sorry. I’m just happy to see that Beoworld and the forum is flourishing again. I’ve had my fair share of involvement with forums struggling during when either doing necessary or unvoluntary changes.

@Tignum : Thanks and the primary source that I want to distribute from the BeoSystem 6500 is the BeoGram as the CD/Radio I have from BeoSystem 9000. So it’s a bit tricky based on that I’m using N.MUSIC to trigger the Moment. With regards to the BL3500 the office I’ve set it up as Link speaker so the Beo4 remote doesn’t trigger the BS6500 and allows me to use the MCP6500 and B&O Audio Terminal remote (the Beolink 1000 which only have the CD, Tape1, Radio, Aux, Tape2 and Phone as sources).

Location: Malmo, Sweden

[Kim]

Hi Guy, and thanks for the welcome but having said that a long users here on the forum, just changed the id and I think this is the 3rd forum setup I’m seeing (sadly as we get a bit cut of and finding old threads/postings including instruction/images). Having said that, it’s great to be back as I kind of lost the interest for the forum when it changes, sadly.

So thanks for the thread link which I kind of recognise my own gear in as I also have a multiroom system but then with ML as primary carier and see that the BS7000 in the provided link is connected to the BLC via the 1611 and then to the NL/LAN so same as I set it up. But, that were I get stuck just can’t get it to play.

Just to line up a few facts on the setup:

• The BS6500 is set to default Option and IR mode nothing changed.
• The BLC dedicated for the BS6500 ML role is set to: A Slave
• The BLC dedicated for teh Moment ML role is set to: Source Center

And then of course the BV10 and BS9000 as expected with the current setup; so N.MUSIC triggers the Moment and plays out via BL8000 connected to the BV10 or several BL3500/BL4000/8000.

Based on the below attached ML-NL network diagram, the BS6500 is currently being used in the office, and that’s were I want to connect it via 1611 to ML-network socket which then is connected to the Technical Room which has the 2 BLC’s.

Location: Malmo, Sweden

[Kim]

What would the scenario be if one would connect a Beosound 6500 system via a 1611 box to existing ML-network which has existing Beosound 9000 and BV10 including a Beosound Moment connected to the ML-network via BLC and have to co-exists with the existing units? Would it be possible to connect the BS6500 via the 1611 to a BLC NL/ML and have it to act as audio slave in the NL-network and still be reachable and output audiot to the rest of the ML-network?

Location: Malmo, Sweden

[Author]

Posts