BV 10-40 problem no picture!

[stotty1111]

Hi all

Got a problem with my 10-40, yesterday, torrential rain here for a short period, Iuse a satelite dish, and I think the rain on the dish affected the detector etc.

Signal returned everything as normal.

This morning switched the set on, just a screen with lots of horizontal interference(?)  and diagonal lines.

It would not respond to changes by the remote.

I have looked at the engineering menu, the monitor info shows build as 127 but it is in red,

Other info, mechanical type BV10-40 model 9570

What should I be looking for/at, suggestions please

More info will be supplied if needed!

Tony

[stotty1111]

Just had a couple of minutes to try the functionality with the connected PC, that works, so, i think it points to the tv section!

Back at it tonight or tomorrow, its a bit time dependant!

[stotty1111]

A little more info:-

MONITOR INFORMATION

Type No    9570

Item No    1847431

Serial No   22073022

 

Option setting    1

Build         127(shown in RED)

 

PRODUCT TYPE

Mechanical Type   BV 10-40

Hardware Type    C22

LCD Panel Type   LTA400HG01

 

 

The set is fitted with a digital satellite card and a terrestrial card,  tuned to UK Freesat and French TNT respectively

 

[Guy]

The Build type in RED is strange.  I searched using AI and it came up with:

The red text for the “Build Type” in your BeoVision 10’s service menu indicates that the television is currently running on engineering, prototype, or non-standard service software, rather than the official consumer release.
This status is an internal flag used by Bang & Olufsen technicians during development, testing, or specific repairs. It is not typically seen on a standard retail unit with regular software updates.

On the Monitor page is there anything listed against the DVB-T/C field?

Or is there a DVB service menu page with DVB CONNECTED shown as YES/NO?

I would double check your satellite connections at DISH and TV end – can you check it with another TV?

If all else fails I would be tempted to note all your settings (if you can view them) and then try a Factory Reset.

• This reply was modified 3 weeks, 4 days ago by Guy.
• This reply was modified 3 weeks, 4 days ago by Guy.

Location: Warwickshire, UK

My B&O Icons:

[stotty1111]

Ok, thanks for that!

No DVB-T/C listed in monitor info or anywhere else.

and in the DVB Service Menu    DVB connected    yes

the Monitor menu5 after those quoted earlier

PW  328

FEP

FEP Bootloader

FA Module

STD Module

System Module

BTB Mdule

DSM FEP

DSM DSP

DVB HD

T CON

I also contacted BnO Tech Support, they have given me a Historic BnO repairer but they are 350miles away near Rouen – last resort I think to visit, I will mail them tomorrow to ask if they have any suggestions / solutions to try.

Meanwhile I will try to locate my list of engineering settings prepared earlier in the year to compare with now  –  it would also give me the working Build number.

• This reply was modified 3 weeks, 4 days ago by stotty1111.

[stotty1111]

Et voila!!!😃

Switched on this morning, still the same situation, looked at the BnO menu page, went to

options, tv setup, ticked both boxes then clicked on DVB and the world opened up.

Could choose language country satellite etc.

And after the next click everything started to reload, after reload had finished rebooted tv and french tv was available and with the sideways arrow to the right freesat came up   —   BRILLIANT, —- I am now a happy bunny!!

I now just need to recreate my personal channel list, a bit of a ballacher, takes a couple of hours, but hey what’s that over paymens to a distant repairer!!!

Monitor info still showing Build 127 in red, I think I can live with that though!😉

Tony a la Finistere

 

• This reply was modified 3 weeks, 4 days ago by stotty1111.
• This reply was modified 3 weeks, 4 days ago by stotty1111.

[Guy]

Great news – have a good weekend!

Location: Warwickshire, UK

My B&O Icons:

[stotty1111]

Have now finished setting up the tv, just checked the Monitor Info area and the Build 127 is now back to black — maybe it’s a no programs loaded thing?

• This reply was modified 3 weeks, 3 days ago by stotty1111.

[Author]

Posts