Beolink ML/NL version number? 1.4, 1.3

[XavierItzmann]

So, I need one of these as I was away during the transition years and all my old equipment is MasterLink and B&O no longer sells this critical component.  Is it true that these are no longer consumer updatable?  What’s a man to do then?

If I buy one, is there a minimum version I should get?  Are there substantial performance differences?  I found an old post here in the forum that cited the final version number but then I lost it.

Thanks in advance.

[Tignum]

Hi Xavier,

Both my BLCs are “1.4.3.19864, December 11, 2015” and they work fine.

Hope this helps. Regards, Johan

Location: Netherlands

My B&O Icons:

[XavierItzmann]

Thank you Johan.

I’ll be asking any sellers about the software version installed on their BeoLink Converter NL/ML, and will only buy if it is 1.4.3.19864 or higher.

[Rolf2]

Hello Xavier,

Johan has mentioned what is to my knowledge the final sw version. Last year, I had to order a repair of one of my BLC ´ s and they needed to exchange the electronics completely. So, more or less a new unit, and it says sw is on 1.4.3.19864. You should be careful indeed, and buy only a BLC with the latest sw version. If it is on a lower level sw version, it may be so because of faulty  electronics.

The sw versions of the BLC are, from latest to older:

1.4.3.19864       – Final version

1.4.3.19816

1.4.2.19611

1.4.1.19522

Those are the ones I know about.

Kind regards,

Rolf

Location: Germany

Favourite Product: BeoSystem 4500

My B&O Icons:

[XavierItzmann]

Ahh, yes, Rolf, thanks for your detailed advice.  The current range of Connected products is set by default on software “auto-update”, so when devices currently updated by B&O cease to be upgraded, most will be left on the final version.

Which prompts me to ask… at the time the BLCs were current, did “auto-update” exist?  Because then you’d be doubly right to question the full functionality of items being sold with less than the final version!

(unless the devices were stored in a drawer, one might think).

[Millemis]

Just checked….

MM

Location: Flensborg————Danmark

[XavierItzmann]

Thanks, MM!

Since these BLC’s had recommended auto-update, most good ones should be on 1.4.3.19864!

Now I just have to get one.

[Rolf2]

Go and grab one and enjoy your ML products working together with NL products!

Kind regards,

Rolf

Location: Germany

Favourite Product: BeoSystem 4500

My B&O Icons:

[Ce Lee]

 

help I cannot upgrade nlml conventer

[Rolf2]

A dealer will be able to upgrade your product. Updating online is no longer available.

Kind regards,

Rolf

Location: Germany

Favourite Product: BeoSystem 4500

My B&O Icons:

[kallasr]

Before installing my newly acquired BLC I wanted to install the latest software (it runs on version 1.4.0.18322).

Just learnt it is not available for download anymore.
It is a shame, it does not update anymore by itself.
Since I do have the software itself, I’d just need the Service Tool MK2+ to install it.

Any chance this can be provided by someone on this Forum?

Thanks in advance.
Ralf

Location: NRW, Germany

Favourite Product: Beo 4

Signature: BV 11-46, BV7-40, BS 4, BS9000, BL11, BL9, BL7-2, BL3, BL4000, BL6000, BL8000, BG4500d, Beoport.

My B&O Icons:

[Author]

Posts