Posts by jimcarr (archived2)
46 total posts39 results
Beovox M70 restored... step by step... well almost...
in Imported Content (Unmapped) · Jan 10, 2019 05:22I did the same speakers and used double sticky tape to put the grills back on. So far that has worked well. Jim.
M70 Speaker repair
in Imported Content (Unmapped) · Dec 10, 2018 00:04Thank you! I'm not sure how I missed your project but now I have the link and of course some questions I posted on it. I read Sorens M70 project but none of the pictures will load up the just say "picture not found". Not…
Beovox M70 restored... step by step... well almost...
in Imported Content (Unmapped) · Dec 10, 2018 00:01Great job!! Now I have a few questions as I am doing some work on my 70's. Did you replace the foam on the front of the speaker? Did you epoxy all of the drivers? It looks like you have to remove the mid range driver fro…
M70 Speaker repair
in Imported Content (Unmapped) · Dec 9, 2018 17:18Thank you! That is what I was looking for. Should I do this to all the speakers? The links talk about just the woofers and I read that some people were having trouble with the phase link speakers. Also I have some S60 sp…
M70 Speaker repair
in Imported Content (Unmapped) · Dec 8, 2018 19:56Hi all! I bought a set of M70's and have been reading about the speaker magnets coming loose. All of my speakers sound good now and I have one grill off (they were glued on) and the speakers pass the finger test. Now I w…
Beovox M70 Mexico
in Imported Content (Unmapped) · Dec 7, 2018 05:16Just found this thread and it was an excellent read but the pictures are gone!! Do you know why?
4002 tracking
in BeoGram · Mar 24, 2018 04:34Hello out there! I am trying to get some tracking issues worked out with my 4002. I have a Hi Fi News test LP. I had my original MMC600 re done but seem to be having trouble setting it up. At 1.1 grams it will not pass a…
4002 speed lights
in BeoGram · Mar 3, 2018 16:50Steveric, Thanks for the info. My deck is a type 5503 from early 1974. I have ordered new led lights from Beolover. Sorry no extra guards. Jim.
4002 speed lights
in BeoGram · Feb 13, 2018 05:16Hi! Anyone know what and or where I can get a speed indicator light? There is only a part number in the manual.
MMC 6000 vs 4000
in BeoGram · Dec 27, 2017 04:35Peter, Thank you for the in depth explanation! I have both and my MMC6000 lost it's stylus back in 84 so I replaced it with the MMC20EN that is now worn out. There is one place that will replace the cantilever & stylus w…
MMC 6000 vs 4000
in BeoGram · Dec 24, 2017 04:02Can anyone tell me if there is any difference between the two besides the stylus & cantilever? Thanks, Jim.
Beogram 4002 cart worn.
in BeoGram · Dec 16, 2017 05:07Thank you for your input. I appreciate reading about the difference in sounds it will help in my decision. I am of the older generation as well as all of my equipment from my first turntable a Dual 1229 now running with …
Beogram 4002 cart worn.
in BeoGram · Dec 15, 2017 03:08So the SMMC20EN is a new cart they make and not a B&O re-build?
Beogram 4002 cart worn.
in BeoGram · Dec 14, 2017 04:16Hello all and Merry Christmas!! Looks like my MMC20EN cartridge is worn out. I tested it using a Hi-Fi News Analogue Test LP and it fails band 7,8 & 9 bias setting on side 1. It pass all tests when I first checked it abo…
Beogram 4002 silent click relay late response?
in BeoGram · Oct 31, 2017 02:48According to my service manual "Adjust 8R2 to admit passage of pickup signal between 1 and 2 disc revolutions after pickup has been lowered" You may want to clean 8R2 first. Jim.
BG4002 tonearm
in BeoGram · Oct 8, 2017 02:57Remove the right rear cover and check the tone arm drive motor and belt.
Beogram 4002 motor's pulley specs
in BeoGram · Oct 1, 2017 20:58Here is what I have. If you need anything more let me know. Overall dia. 35mm Belt dia. 28mm Overall height 11mm Belt height 8.5mm I'll post pics when I figure out how. Jim.
4002 tonearm lifts
in BeoGram · Sept 4, 2017 03:56Well it looks like I have found the problem!!! An intermittent open base-emitter junction on 0TR4!. It's only taken 2 years but It's working great now. It finally went out long enough to get the readings I needed and was…
4002 tonearm lifts
in BeoGram · Apr 3, 2017 03:05Well I'm still at it. My deck worked just fine for about 2 months then the problem came back. I have replaced transistors 1TR14, 1TR15 & 1TR16 with no help. Also when I monitor the base of 1TR14 there is no change at all…