Posts by JoDap (archived2)
23 total posts20 results
BeoLab 3500 IR receiver issue
in Imported Content (Unmapped) · Feb 13, 2022 21:13Congrats on getting it to work again! For future reference: the long leg (anode, +) goes in the round hole, while the short leg of the LED (cathode, -) that is on the flat side of the "bulb" goes in the square hole.
BeoLab 3500 IR receiver issue
in Imported Content (Unmapped) · Jan 29, 2022 22:05I did the same thing! I actually never replaced it, because it was the one for the timer and I never use the timer anyway. My guess (!) would be if you get any red LED with the right diameter it should be fine.
BeoLab 3500 IR receiver issue
in Imported Content (Unmapped) · Jan 13, 2022 21:19Yes it is that one, I'm afraid. I know I wrote, that it might be doable without removing the plastic stuff above, but I haven't tried it and I wouldn't recommend it if your not very used to soldering in tight spaces. So …
Beosound 9000 Mk2 - PCB41 issue?
in General Discussion & Questions · Sept 3, 2020 08:33Sorry, I can't provide an answer, but I have exactly the same problem with my Ouverture: Laser turns on and moves around, but in the motor spin test mode, the CD starts spinning clockwise for a second and then spins anti…
BeoCenter 2300 dead after opening it
in Imported Content (Unmapped) · Feb 12, 2020 06:31Tusind tak! I'll check it out
BeoCenter 2300 dead after opening it
in Imported Content (Unmapped) · Feb 9, 2020 12:59From a first look it seems that everything is as it should be. The only wire I had to detach is a ground wire (I suppose it's ground) that sits on one of the screws holding the wire pulleys. That one I connected again. B…
BeoCenter 2300 dead after opening it
in Imported Content (Unmapped) · Feb 8, 2020 22:40Hi, I replaced the rubber belt that drives the glass doors on my BeoCenter 2300 (2616). I did it from the backside, so without unmounting any PCB. I even managed to not take the wires out: it turns out you can roll the r…
BeoLab 3500 IR receiver issue
in Imported Content (Unmapped) · Feb 13, 2019 21:04Thanks again, replacing the cap worked! If anyone is having the same problem: if you don't want to unmount the plastic casing on the PCB you could probably fix it without doing so. The capacitor in question is all the wa…
BeoLab 3500 IR receiver issue
in Imported Content (Unmapped) · Feb 5, 2019 21:28Thanks a lot, I will try that!
BeoLab 3500 IR receiver issue
in Imported Content (Unmapped) · Feb 5, 2019 21:28Thanks a lot, I will try that!
BeoLab 3500 IR receiver issue
in Imported Content (Unmapped) · Feb 2, 2019 08:38Unfortunately it didn't work. I tried both with the remote in link mode and the regular one. I also teiwt acessacce the service menu, but no response.
BeoLab 3500 IR receiver issue
in Imported Content (Unmapped) · Feb 1, 2019 22:04Thanks, I'll try that, but with option 4 as the units are in the same room. Do I point the remote at the BL3500 for the setting or at the BS9000 (connected via beolink wireless 1)? Cheers, Johannes
BeoLab 3500 IR receiver issue
in Imported Content (Unmapped) · Feb 1, 2019 17:29Hi, I have a problem with my BeoLab 3500 :-( The other day I had to unplug it for a while and since then it doesn't take any commands from my beo4 anymore. I tried two different remotes (beo4) and also made sure that the…
Is Wireless 1 compatible with Beomaster 4500 and BeoLab 3000?
in General Discussion & Questions · Nov 9, 2015 21:51Hi Carl, I'm using Wireless 1 in my home, and am relatively satisfied with it. I use it to connect my Beosound 9000 with a Beolab 2000 in an adjacent room (so I use Masterlink on both ends). The transmitter and receiver …
Interested in controlling your ML setup with a Raspberry Pi?
in General Discussion & Questions · Nov 3, 2015 22:16Great, just let me know when you have some more input on that
Interested in controlling your ML setup with a Raspberry Pi?
in General Discussion & Questions · Nov 3, 2015 22:15Great, just let me know when you have some more input on that
Interested in controlling your ML setup with a Raspberry Pi?
in General Discussion & Questions · Nov 2, 2015 20:58Hi, I would also take 2, potentially 3. One question, though: do you think it would be possible to communicate with Beolink Wireless as well or is anyone else working on that? The main reason why I am asking is, because …
Beosound 9000 MK I skips tracks after a while
in General Discussion & Questions · Nov 2, 2015 19:57Hi, Thanks for your reply. That was also what I thought, but this is the actual unit inside my BS 9000 (type 2621) I have also another picture here that shows the position of the light pen when it is supposed to be all t…
Beosound 9000 MK I skips tracks after a while
in General Discussion & Questions · Nov 1, 2015 19:34Hi again, I have a short update: Today I investigated the matter a bit more systematically and I found that the skipping is not dependent on time, but on position of the laser head. I.e. always around tracks 8 - 10 the p…
Beosound 9000 MK I skips tracks after a while
in General Discussion & Questions · Oct 31, 2015 13:23Hi, I am newly registered here, after having read in the forum for a while. So I hope that I got the right subforum for my question. The problem with my BS9000 MK I is not unique as I see it, and there have been numerous…