Posts by judgefilip (archived2)
17 total posts13 results
TX-2 - Static noise from the speakers as the tonearm raises and lowers
in Imported Content (Unmapped) · Jun 27, 2016 15:40I had this issue with one of my Beograms. I guess it's the malfunctioning muting switch. You have to either replace it or treat it with some kind of spray-on formula to remove oxidation and lubricate it at the same time.…
9500 CD jumping on spindle - video link attached
in Imported Content (Unmapped) · Jun 27, 2016 15:27There should be a rubbery black ring on the outer edge of the spindle's disc. It may wear off causing the CD inserted to slip. This may cause problems to the drive with recognition of the disk inserted. I had this issue …
Linking Beosystem 7000 and Beosound 9000
in General Discussion & Questions · May 14, 2016 00:34Could somebody please tell me if the following setup is possible? I have a Beosystem 7000 in the living room and a Beosound 9000 in the bedroom. Would it be possible to link those products using ML Converter linked to th…
Beocord 6500 adjustment
in Imported Content (Unmapped) · Oct 25, 2015 20:12Everything's clear. Time to upgrade my membership!
Beocord 6500 adjustment
in Imported Content (Unmapped) · Oct 25, 2015 20:05My brother who used to own silver memberhip here dowloaded the manual from this site and it lacked pages regarding adjustments. Can you confirm that service manual for BC6500 or BC7000 is actually a full service manual? …
Beolab Penta mains hum / buzz noise
in Imported Content (Unmapped) · Oct 25, 2015 12:39Have you performed the no-load current adjustment? Connecting DC millivoltmeter between R103 and R104 should give 30mV. Otherwise adjust R95 accordingly. Speakers have to be disconnected from amplifier which needs to be …
Beocord 6500 adjustment
in Imported Content (Unmapped) · Oct 25, 2015 12:26Could somebody who owns a complete BC6500 service manual be so kind and send me just two pages regarding electrical adjustments? I need to know where the test points are located. Best regards
Beocord 6500 adjustment
in Imported Content (Unmapped) · Oct 20, 2015 15:17Hello Everyone, I had to adjust the azimuth of the tape head of my Beocord 6500, as recordings made on B side were dull compared to side A. I've acquired suitable reference tape to do so and the sound quality is now grea…
Beogram CD 6500 stand-by issue
in Imported Content (Unmapped) · Sept 28, 2015 22:24Currently: BM6500 SW 1.5, BM7000 SW 1.1 I happen to have a SW 1.7 EPROM file for BM6500 that Dennis from this forum sent me once. I never actually managed to update it. Do you know if the 27C512 chip is suitable to write…
Beogram CD 6500 stand-by issue
in Imported Content (Unmapped) · Sept 27, 2015 15:10Thanks for your quick response! I've measured DC voltage across pins 2 and 3 of 7805 voltage stabilisers and for IC1 it is exactly 5V and IC2 gives 5.144V. I've also checked the player with my other Beomaster 7000 - it b…
Beogram CD 6500 stand-by issue
in Imported Content (Unmapped) · Sept 27, 2015 02:45Hello everyone, My Beogram CD 6500 has developed a strange issue. As I remember correctly it used to work like this: when listening to CDs and switching to another source for example radio, Beogram used to go into pause …
Beomaster 6500 tuner issue
in Imported Content (Unmapped) · Nov 19, 2014 14:54Thanks for your response Die_Bogener! Desoldering all connection sockets both on CPU board, tuner pcb and preamplifier boards didn't help, but I've found the problem! It was caused by bad C66 cap. Although I've replaced …
Beomaster 6500 tuner issue
in Imported Content (Unmapped) · Oct 31, 2014 21:35Hello everyone, My BM6500 has developed an issue with its tuner. A while ago I replaced old caps in audio signal path, power supply, CPU board and front PCB (to improve two-way ir communication). Unit works really well, …