Posts by bzuidgeest (archived2)
16 total posts13 results
Help getting beomaster open
in Imported Content (Unmapped) · Oct 31, 2015 17:44Hi Martin, I spend an hour wiggling that cover before I wrote this post. But at your suggestion I tried again and nothing. I then inserted a screwdriver just above where the black wire comes in and it finally popped off.…
Help getting beomaster open
in Imported Content (Unmapped) · Oct 31, 2015 16:25Ok, I feel really stupid asking as question like this, but how do you get the cover of the tone control section from a beomaster 2200 off? I cannot find any screws or clicky things. I tried by removing the complete botto…
replacing panel light with leds on beocenter 2100
in General Discussion & Questions · Jun 3, 2012 16:31For now I have ordered the lamps from dillen. Considering how they are used in the dail of the 2100 that seems to be the best option. Taking us back to the discussion about led or lamp. I just refitted an Marantz (yes I …
What Are You Working On Now
in Imported Content (Unmapped) · Jun 3, 2012 14:08No you did not, I looked again and the painting was eugene. I got confused with you both making white panels in such different ways.
What Are You Working On Now
in Imported Content (Unmapped) · Jun 3, 2012 13:56That letraset stuff is expensive! At least the custom transfer stuff which I would need for the bottom images... Other question. Did you paint the panels or did you tape them over? either is suggested in your previous po…
replacing panel light with leds on beocenter 2100
in General Discussion & Questions · May 29, 2012 18:53For now I think I will just get the lamps from dillen, but thank you for the info. He already responded to my email. I did not expect the lamps to last for more than a few years longer than normal room lights. they are s…
What Are You Working On Now
in Imported Content (Unmapped) · May 29, 2012 18:37To answer both dillen and leslie's questions. It is the bottom plate of a beomaster 2200. It's nothing special. But I wanted to see what could be done for what cost and it seemed like the perfect candidate for an experim…
What Are You Working On Now
in Imported Content (Unmapped) · May 28, 2012 12:53Leslie, Looking at your fine work you seem to be the man to ask this. I got my hands on a beomaster that looked like it was stored somewhere very humid. It had rust all over the bottom plate. I had it sanded and powderco…
Help with B&O spares
in Imported Content (Unmapped) · May 28, 2012 11:46I have a 1902 turntable sitting in the attic which unfortunately has reached spare part condition only. It has two counterweight on the back the big block and the smaller one for fine tuning. If you have not found your c…
replacing panel light with leds on beocenter 2100
in General Discussion & Questions · May 27, 2012 16:40Hi Martin, It's not about replacing lamps being a big problem. It's more like I would not know where to get the correct ones (most times, and some bulbs are expensive to). If I take the wrong bulbs I risk them producing …
replacing panel light with leds on beocenter 2100
in General Discussion & Questions · May 27, 2012 14:19The beocenter 2100 uses two light bulbs to illuminate the front panel. Part number is 8230048 skalalys dail light. I can easily replace them with warm white leds which will last forever. The problem is that I don't know …
switch for beomaster 2200
in General Discussion & Questions · Mar 29, 2012 18:01I'm trying to fix up an beomaster 2200 system. I just fixed it's power supply, but after that I discovered that the switch that selects am / lw does not latch anymore. Took it appart but could not fix the switch. There a…