Posts by espen
17 total posts14 results
Beogram 4004 lifting tonearm late?
in BeoGram · Sept 27, 2020 10:30I have a 4004 and it seems the tonearm assembly starts traveling back before the stylus is lifted. Please check my video of the behavior here: https://youtu.be/Wq0_xjjPtvQ Is this normal or do I need to adjust something …
Beolab 2 issue?
in General Discussion & Questions · Jul 13, 2020 20:39Ok, not sure if i can get it to work, but ill try.I was unable to load from site library.
Beolab 2 issue?
in General Discussion & Questions · Jul 13, 2020 17:46Hi, Picked up a Beolab 2 and it has this ring/inprint about 5-7 cm diameter in the center of the bass driver, and i dont know if this is an issue or if it is normal. It was not visible in the picture or the light i revie…
Interested in controlling your ML setup with a Raspberry Pi?
in General Discussion & Questions · Mar 1, 2016 12:18Just pulling this one up in hope for any news :)
BV10 behaviour on source switch after puc update
in General Discussion & Questions · Dec 17, 2015 11:00Hi, I had the local B&O dealer over for an update to the puc list in my BV10-46. After his visit there has been a change in the behaviour of the tv when switching source. When I press a new source on the beo4, i.e. TV, w…
Interested in controlling your ML setup with a Raspberry Pi?
in General Discussion & Questions · Sept 11, 2015 09:53Hi, I would also prefer the RaspberryPi. Same reasons already mentioned by others. And great to see work is still ongoing :) Regards, Espen
Interested in controlling your ML setup with a Raspberry Pi?
in General Discussion & Questions · Jun 18, 2015 12:38Just want to add that i would take 3 boards. 🙂 Regards Espen
Interested in controlling your ML setup with a Raspberry Pi?
in General Discussion & Questions · Jun 15, 2015 20:10I have been reading your dev thread with great interest. I am also VERY interested, so sign me up! :) Regards Espen
Light controller with arduino
in General Discussion & Questions · Jan 15, 2014 07:37I put in small orders from these ebay sellers, no problems at all. All delivered fine within reasonable time: http://www.ebay.com/itm/VISHAY-TSOP7000-DIP-3-IR-Emitting-Diode-Power-/221241394076?pt=Bauteile&hash=item33830…
Have B&O gone mad with their prices?
in General Discussion & Questions · Dec 28, 2008 09:39The comparison to cars is not a good one in my book. Besides four wheels and a steering-wheel a Ferrari hardly compares to my car at all, both looks and performance, its in another league all together. As for other luxur…
bv7-40 motorized floor stand diameter
in General Discussion & Questions · Aug 29, 2008 08:55http://www.bang-olufsen.com/UserFiles/File/ts/BeoVision7_en.pdf
Problems with Sky on a BeoVision 7-40 Mark II
in General Discussion & Questions · Oct 20, 2007 21:15Hi, Dont know what kind of setup you have, but to fix a similar problem to what you are describing i had to change the kind of screen (16:9/4:3) and what to do with the signal in my STB. This was for a bv 8/32. Have a ni…
Beovision 7 verses 9
in General Discussion & Questions · Oct 17, 2007 09:06Hi all, http://cache.aftenposten.no/multimedia/archive/00615/Pioneerkontrast_615009a.jpg From this article: http://forbruker.no/digital/tester/tv/article2002501.ece The picture shows a comparison between a new pioneer an…