Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

traverso

Forum Replies Created

Viewing 18 posts - 1 through 18 (of 18 total)
  • Author
    Posts
  • in reply to: Beomaster 1900 IL1 Testing #49878
    traverso
    BRONZE Member

    The LDR components were the culprits

    I used a repair kit from Beoparts and put back the LDR in the 1900, everything is fine

    The 1900 is back to life and sing again

    Thank you Sonavor

    in reply to: Beomaster 1900 IL1 Testing #49877
    traverso
    BRONZE Member

    Actually I unsoldered the LDR, more easy to open it

    The metal cover is glued to the black plastic support see attached picture

    The lamp is dead

    LDR BM 1900

    in reply to: Beomaster 1900 IL1 Testing #49876
    traverso
    BRONZE Member

    The lamp is probably OK as measured 17 Ohms

    However I have ordered a repair kit for this LDR

    By the way, is there a trick to remove the cover of this LDR? Is it glued or just clipped?

    in reply to: Beomaster 1900 IL1 Testing #49875
    traverso
    BRONZE Member

    Hello,

    Thank you for the help

    I used a one Khz tone generator connected to the recorder input  and the signal arriving at the balance control is very low

    I will open the LDR by tomorrow for checking

    Alain

    in reply to: Beomaster 1900 IL1 Testing #49873
    traverso
    BRONZE Member

    I could measure the IL1 lamp resistance between emitter TR24 and 15 V and found 17,7 Ohms is this value OK?

    If yes the problem is elsewhere, any thought?

    in reply to: Beomaster 3400 Problems #41363
    traverso
    BRONZE Member

    I lately discovered your message

    Concerning the Service Manual I may send it  if you are still interested.

    Cheers

    Alain

    in reply to: Beomaster 2400 cannot switch to FM5 ! #46899
    traverso
    BRONZE Member

    The culprit was R126 measured 40 MOhms

    in reply to: Beomaster 2400 cannot switch to FM5 ! #46898
    traverso
    BRONZE Member

    Yes!

    I used FM4 to activate FM5 and it works as follows:

    • the R122 and R126 lifted from the IC6 side
    • the R122 connected in place of R126 on IC6 side

    So the issue is between TR21 and the IC6, to confirm I have to replace this R126 or look for broken copper track

    Thanks a lot Martin

    in reply to: Beomaster 2400 cannot switch to FM5 ! #46897
    traverso
    BRONZE Member

    The signalling only is on an other PCB not the commands

    in reply to: Beomaster 2400 cannot switch to FM5 ! #46894
    traverso
    BRONZE Member

    Yes it was always there

    (By the way I measured the lamps they are 18 Ohms each instead of 12/14 Ohms as a consequence, the voltage reference for muting measured at R3, 33Ohms of PCB 5 is no longer 2,5 Volts but 1,9 Volt)

    in reply to: Beomaster 2400 cannot switch to FM5 ! #46892
    traverso
    BRONZE Member

    No it does not if I am on an other entry

    However, it starts the 2400 when in stand by but does not allow to use FM5 the corresponding lamp is not lit, but in that case I may switch to any other input

     

    Alain

    in reply to: Beomaster 4400 faulty issue #46298
    traverso
    BRONZE Member

    actually it was one leg of the P6 switch to be grounded, stangely it was not.

    If left open the front end is missing the voltage for the varicaps and it is free running

    in reply to: Beomaster 4400 faulty issue #46297
    traverso
    BRONZE Member

    Hello

    After checking some parts ofthe 4400, it appears that one end of the P6 pot for adjusting the channel number 6 is left open when it should be grounded. To be corrected of course. Hopefully can be done without difficulties.

    Cheers

     

    Alain

    in reply to: Beomaster 4400 faulty issue #46296
    traverso
    BRONZE Member

    Hello,

    I have here a new behavior of my 4400 unit I dont know how to correct.

    When switching from an FM selection to Tape 1 or 2, or Phono, the display related to FM stereo lamp and tuning indicator remains lit for sometimes up to 10 seconds and then disappear.

    It does not affect the sound and functioning . The 15V still there during this time, how to corect this ? Is TR1 involved and  how?

     

    Alain

     

    in reply to: Beomaster 4400 faulty issue #46295
    traverso
    BRONZE Member

    OK thank you Jacques

    in reply to: Beomaster 4400 faulty issue #46293
    traverso
    BRONZE Member

    Thanks for your feedbacks

    I will look at it accordingly, since then the situation changed and now when switching on a big bump occurs immediately and the unit is working

    I rememeber the previous 4400 I repaired there was a 2 to 3 seconds delay before the unit started, this one no delay, can we adjust this and how?

    Many thanks

    Alain

    in reply to: Beomaster 4500 RIAA PCB and SW upgrade #40024
    traverso
    BRONZE Member

    Seen your message

    I will Paypal you now 89 Euros

    Thank you for taking care

    Cheers

    Alain

    in reply to: Beomaster 4500 RIAA PCB and SW upgrade #40023
    traverso
    BRONZE Member

    ok great!

     

    I answered my interest answering your email

    tell me if you received it

    cheers

    Alain

     

     

Viewing 18 posts - 1 through 18 (of 18 total)