BeoWorld Logo
Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

mark. hinks.

Forum Replies Created

Viewing 11 posts - 1 through 11 (of 11 total)
  • Author
    Posts
  • 1 October 2025 at 10:47 in reply to: Beogram 5500 start stop microswitch not doing anything. #70020
    mark. hinks.
    SILVER Member

    okay scrap the previous post ..  it was  the the centre weight detector not going down far enough.

    Any way to adjust that?

    what happens now is it spins normally for a few seconds but the small lift cam rotates around to almost the start position .. record on or off .

     

    Location: United Kingdom

    1 April 2025 at 16:35 in reply to: beogram 3000 /1202 etc tone arm removal ?? #64856
    mark. hinks.
    SILVER Member

    i managed to unblock and thread litz wire through.

    Location: United Kingdom

    28 February 2025 at 10:07 in reply to: beomaster 3500 glass panel broken #64183
    mark. hinks.
    SILVER Member

    I feel you may be right about the addiction.

    Yes keeping my eyes open for a bm3500.

    Location: United Kingdom

    1 January 2025 at 15:51 in reply to: beocenter 9300 how to remove glass panels #62147
    mark. hinks.
    SILVER Member

    Hi Guy, it’s working and saving presets.

     

    I did a mother board trick as you suggested and shorted the battery.

    I also gave the battery a wiggle

    I’m so happy 😁

    No doubt I’ll be back but thank you so much for all your time and trouble over this new year.

    All I can say is, your input wasn’t wasted!

    All I have to do now is find a remote control.

    Regards to you .

     

     

    Location: United Kingdom

    1 January 2025 at 13:52 in reply to: beocenter 9300 how to remove glass panels #62143
    mark. hinks.
    SILVER Member

    Bugger, the battery is good and has power to the board.

    Tested with voltmeter.

    Anyone got any thoughts.

    Could it be resolved by something in the manual programming or maybe with a remote control.

    Otherwise I’m stumped. 🧐

    Location: United Kingdom

    1 January 2025 at 13:27 in reply to: beocenter 9300 how to remove glass panels #62139
    mark. hinks.
    SILVER Member

    Thanks..

    Ill update when done.

    Location: United Kingdom

    1 January 2025 at 12:41 in reply to: beocenter 9300 how to remove glass panels #62134
    mark. hinks.
    SILVER Member
    1. IMG20250101123307IMG20250101123918IMG20250101123256IMG20250101123243

    <!–more–>

    Location: United Kingdom

    1 January 2025 at 12:38 in reply to: beocenter 9300 how to remove glass panels #62132
    mark. hinks.
    SILVER Member

    I’ve located battery.

    I can’t see any soldering on top, is it soldered on the other side?

    Are the white pads under the battery normally there?

    Could you have a look at supplied photos.

    Thanks.. I’m very close now.

    Location: United Kingdom

    31 December 2024 at 17:38 in reply to: beocenter 9300 how to remove glass panels #62101
    mark. hinks.
    SILVER Member

    Followed instructions,

    Made a couple of errors but all buttons up and working perfectly.

    I could see the glass panels had been dodged slightly before.

    I’m now thinking the battery is probably the problem.

    Is it a desolder and solder job?

    I’ll need a second hand remote.

    My finances are pretty rubbish.

    Location: United Kingdom

    31 December 2024 at 17:35 in reply to: beocenter 9300 how to remove glass panels #62099
    mark. hinks.
    SILVER Member

    <!–more–>IMG_20241231_150319IMG20241231161203

    Location: United Kingdom

    30 December 2024 at 20:06 in reply to: beocenter 9300 how to remove glass panels #62074
    mark. hinks.
    SILVER Member

    Thanks for such a detailed and clear response.

    I’ll have a go at everything you suggest and get back to you.

     

    Id like to get this work of art in good condition.

     

    What is the situation with replacement remote control for the 9300.

    I don’t mind aftermarket .

     

    Thanks 🙏

     

     

    Location: United Kingdom

  • Author
    Posts
Viewing 11 posts - 1 through 11 (of 11 total)