Posts by alltvrepairs (archived2)
23 total posts17 results
Any BeoVision 4 (50-65) Owner or knowledgeable person! Required IR sensor name or PCB
in General Discussion & Questions · Jan 28, 2013 20:55Hi, Am still struggling to get the BS3 (Mark 2) and BV4 working after months of frustration :( Is there a kind soul that can confirm the IR sensor name located on the PCB under the half round plastic top cap. There is a …
Beo4 keypad issue
in Imported Content (Unmapped) · Jan 25, 2013 06:25Hi , You can check with this table to see if all contacts are ok. Good Luck, AllTvRepairs
Beo4 keypad issue
in Imported Content (Unmapped) · Jan 25, 2013 06:25Hi , You can check with this table to see if all contacts are ok. Good Luck, AllTvRepairs
BeoSystem3 not communicating with BeoVision4
in Imported Content (Unmapped) · Jan 22, 2013 18:27Hi Alex, I have the original B&O serial cable connected and have checked pinouts. Could it be the unit is locked or waiting for a DVB tuner connection? I have tried DVD, HDMI input but to no avail :(
BeoSystem3 not communicating with BeoVision4
in Imported Content (Unmapped) · Jan 22, 2013 17:59Unfortunately both suggestions didn't work out. Tried a crossed RS323 link and also V.OPT 1 as Casper suggested :( UPDATE: I have found that I have some video output from AV1 and AV2 scarts only. There is a timer like ic…
BeoSystem 3 locked or faulty? Suggestions pls !
in General Discussion & Questions · Jan 22, 2013 14:34Unfortunately both suggestions didn't work out. Tried a crossed RS323 link and also V.OPT 1 as Casper suggested :( UPDATE: I have found that I have some video output from AV1 and AV2 scarts only. There is a timer like ic…
BeoSystem 3 locked or faulty? Suggestions pls !
in General Discussion & Questions · Jan 21, 2013 08:51I will try it later today as I am currently out. However very anxious to try it out and let you (everyone) know the outcome! Thanks a lot Casper.
BeoSystem 3 locked or faulty? Suggestions pls !
in General Discussion & Questions · Jan 21, 2013 07:31Hi, I have hooked up the Beosystem 3 to a Beovision 4 . When powering up, a green LED on the Beosystem is on for 30 seconds and then switched OFF again. At this time the Standby RED LED on top of the TV (Link eye pcb?) i…
BeoSystem3 not communicating with BeoVision4
in Imported Content (Unmapped) · Jan 19, 2013 14:08Hi, My problem s that I am not able to switch on TV and don't know if I have a fault or not. I have hooked up the Beosystem 3 to a Beovision 4 65" Plamsa (by Panasonic). When powering up the Beosystem, a green LED on the…
How to remove BeoVision 4 65" from its floor supporting stand (see picture)
in General Discussion & Questions · Dec 8, 2012 16:25Hello again, We have tried to lift off the Tv from its stand but we couldn't move it at all. I am not sure if there is a locking pin somewhere or is just damn heavy. Someone had some experience in this? Thanks!
BeoSystem 3 Testing if working or not.
in General Discussion & Questions · Dec 8, 2012 16:02Thanks for your replies Hfat and Beojeff. I have downloaded the user and service manuals and was reading again and again. For external IR I found this linkinteresting http://www.beoworld.org/beotech/ir_eye_wiring.htm I w…
BeoSystem 3 Testing if working or not.
in General Discussion & Questions · Dec 7, 2012 14:27Hi, I have difficulty in identifying if I have a Faulty BeoSytem 3, Or BeoVision 4 or both. I have 2 questions: 1) Is it possible to connect a BeoSystem 3 to an LCD or TFT and be able to see some picture to see if it is …
BeoVision 4. Problem in Rear Connection.
in General Discussion & Questions · Dec 5, 2012 20:52I have just purchased a reasonable Gold Membership.
BeoVision 4. Problem in Rear Connection.
in General Discussion & Questions · Dec 5, 2012 18:26Hi Beojeff , Tought so as I found an IR receiver along with other circuitry for picture calibration, but thanks for confiming. So don't you think that I should have found some voltages there? I assume that the Panasonic …
BeoVision 4. Problem in Rear Connection.
in General Discussion & Questions · Dec 5, 2012 14:38Good to know. I have uploaded a photo of the Beosystem connections. The strange thing is that I have removed the IR sensor cap on top of tv and checked for some voltage. There should be a small voltage typically 5v DC bu…
BeoVision 4. Problem in Rear Connection.
in General Discussion & Questions · Dec 5, 2012 12:29Thanks for your response. I think I can find a spare Panasonic remote control. But I assume that I should see a standby LED lit somewhere with the mains plug on.. or not? Do you know something about the 3 bottom connecti…
BeoVision 4. Problem in Rear Connection.
in General Discussion & Questions · Dec 5, 2012 10:10Hi, this is my First Post as couldn't find a similar post. As a TV Engineer I have been hired to hook up Beovision 4 (65 Plasma) and BeoSystem 3 after client moved house. I have connected all the connections apart from o…