Posts by loris (archived)
97 total posts89 results
One channel only in a 5500
in BeoGram · Feb 26, 2010 09:16well.... "much ado for nothing". I tested the connection from point 3 and 5 of the muting board and the exit din pins. The red cable ( right channel) was interrupted 🙂 So I decided to dismantle that "well packed" din so…
One channel only in a 5500
in BeoGram · Feb 26, 2010 04:58Hi Peter, thanx for the answer. I'm at work now so I cant' check, but I'm almost sure I'll find that there's no continuity in the right channel. How do I go deeper into the issue?
One channel only in a 5500
in BeoGram · Feb 26, 2010 03:31Hi all, suddently one channel died. I have left channel only. I checked the amp and it's not. Then I checked the cartridge turning it upside down but it's not. Could you please tell me how do I check where the fault is (…
SMMC4
in BeoGram · Oct 8, 2009 04:42Henrik, if you're interested I have a SMMC4 for sale. I bought it in may and it has 20 hours of listening. I've switchd to a Beogram 6000. Loris
Beogram 6000 / 4002 Problems and Solutions
in The Workbench · Sept 19, 2009 18:33I definitely solved the problem running a wire from pin 5 of the 9 pin plug to the earthing screw of the amp :-) Loris
Beogram 6000 / 4002 Problems and Solutions
in The Workbench · Sept 15, 2009 15:58[quote user="tournedos"] You probably need to run a ground wire from the chassis of the Beogram to the earthing screw on your amp. [/quote]Well I did this but a certain amount of hum (unacceptable) did remain. I did a lo…
Beogram 6000 / 4002 Problems and Solutions
in The Workbench · Sept 8, 2009 05:48Hi Manahem, actually I didn't solve the problem. After the removal of the phono board, I did the right connections, I have left and right signal but I still have a lot of hum. I hadn't much time to look inside the proble…
Beogram 6000 / 4002 Problems and Solutions
in The Workbench · Aug 2, 2009 16:39I run a wire from the earthing screw of the amp to the ground of the din exit cable, where there's a cap between the wire and the chassis. Completely no hum but the sound is poor. I'll check why. Loris
Beogram 6000 / 4002 Problems and Solutions
in The Workbench · Aug 2, 2009 05:33I removed the riaa/cd4 board and made this connection, but the hum is higher than the music. I checked the cable and it's ok, but always high hum... Loris
Beogram 6000 / 4002 Problems and Solutions
in The Workbench · Jul 31, 2009 04:41Even if I'm not much into electronics, according to the manual ( section 3/11) this operation can't be done. There are 3 pins with 12V dc for the power supply of the Riaa/cd4. Loris
Beogram 6000 / 4002 Problems and Solutions
in The Workbench · Jul 30, 2009 16:04I removed the riaa/cd4 boards. If I connect the 9 pin male plug to the 9 pin female will I harm something? Will I get a standard 4002? thanx Loris
Beogram 6000 / 4002 Problems and Solutions
in The Workbench · Jul 29, 2009 17:50[quote user="auric"]You may also try to swap L+R wires inside the din shell. If the lower output channel moves from one to the other then it is likely also the cartridge. [/quote] this is true if there isn't a phono stag…
Beogram 6000 / 4002 Problems and Solutions
in The Workbench · Jul 29, 2009 09:16Hi, R U all in vacation? 🙂 What should I do now? Loris
Beogram 6000 / 4002 Problems and Solutions
in The Workbench · Jul 25, 2009 08:12I thought I had fixed the problem. I remade solder connections inside din cable and cleaned the 5 pins.But the image is still on the right. Loris ps Manahem, thanx for your offer. Will it be an easy task? I don't even kn…
Beogram 6000 / 4002 Problems and Solutions
in The Workbench · Jul 22, 2009 03:42I'll start to check 🙂 Loris
Beogram 6000 / 4002 Problems and Solutions
in The Workbench · Jul 21, 2009 16:21I have another problem🙁 the left channel is lower than the right one. I have an image between the center of the speakers and the right one. I swapped the speakers and changed the input from aux to tape 1 and it's the sa…
Beogram 6000 / 4002 Problems and Solutions
in The Workbench · Jul 21, 2009 07:58Well Beoworld community, with your help now everything seems fine and I like the sound of this turntable (along with the beomaster 5500 and beovox s60 speakers). Later I'll check all the arm setups. Now I have a problem:…
Beogram 6000 / 4002 Problems and Solutions
in The Workbench · Jul 18, 2009 03:16.... and the light was..... the lamp worked.... but the carriage didn't 🙁 I had to work on the "adjustment of shutter". I moved a little the "eccentric B" ( page 4-7 of the manual) and then for the first time the carria…
Beogram 6000 / 4002 Problems and Solutions
in The Workbench · Jul 16, 2009 03:51[quote user="yachadm"]Glueing the leads:[/quote] Nice idea. I thought about hot glue but I switched to paper glue in stick. It's a paste I could easily put inside the cavity and I guess I'll be able to easily remove it. …
Beogram 6000 / 4002 Problems and Solutions
in The Workbench · Jul 15, 2009 05:01This is the new lamp in the enclosure ( waiting for the glue to dry ) and the old burnt lamp with the hardened glue around the wires