Posts by sparker62 (archived)
33 total posts30 results
Fitting STB-C to MX4002
in General Discussion & Questions · Jul 3, 2007 16:29Thanks for the info Peter, I have now programed the STB-C to code2 but I am still not getting any response................!!🙁 I will have to check all the connections during the weekend. I did notice that when I disconn…
Fitting STB-C to MX4002
in General Discussion & Questions · Jul 2, 2007 10:19Peter, I have found instructions in both Dutch and German.....but no English! It looks straight forward enough but I want to make sure I program it right if I only get one hit!!😝 Simon
Fitting STB-C to MX4002
in General Discussion & Questions · Jul 2, 2007 09:28Peter, do you know what software version was on your STB-C? I am just checking that code2 is definitely correct for my version of STB-C before I try programming it! Thanks, Simon
Fitting STB-C to MX4002
in General Discussion & Questions · Jul 2, 2007 03:28I wasn't aware of that Peter! I didn't have the relevant sheet of paper. I thought I set it with an on screen menu!! Yes, the software chip is present. I checked after reading your earlier mail!😐 It has software version…
Fitting STB-C to MX4002
in General Discussion & Questions · Jul 2, 2007 02:47Peter, I haven't found any new menus to allow me to set the AV2 scart to the STB-C and then to the Sky Box as code 2! Where do you access the new menus? I have a user guide for an Avant or AV5 but as stated earlier I hav…
Fitting STB-C to MX4002
in General Discussion & Questions · Jul 1, 2007 16:31Well I've fitted the stb-c but nothing works!! It took me a little while to find where everything went using the guide but all seemed to go well........!? When I connected up the Sky Box to AV2 and switched on MX I went …
Fitting STB-C to MX4002
in General Discussion & Questions · Jul 1, 2007 16:31Well I've fitted the stb-c but nothing works!! It took me a little while to find where everything went using the guide but all seemed to go well........!? When I connected up the Sky Box to AV2 and switched on MX I went …
Fitting STB-C to MX4002
in General Discussion & Questions · Jun 29, 2007 16:25Thanks Peter, I plan to fit the STB-C on Sunday if the weather is bad........!! Hope it is less taxing than it was for Terry! Regards, Simon
Fitting STB-C to MX4002
in General Discussion & Questions · Jun 27, 2007 09:33As usual Peter it depends how hard the dealer tries.............
Fitting STB-C to MX4002
in General Discussion & Questions · Jun 27, 2007 08:48Hello Peter, yes I downloaded the manual and all looks fine there, but I have seen other material ie schematic overviews and STB-C listings which specifically exclude the 784x model. There is no explaination why! Also th…
Fitting STB-C to MX4002
in General Discussion & Questions · Jun 27, 2007 07:35when I looked at fitting a STB-C to my MX all the guides do not list the 784x type. What stops me from fitting one to this model? Is there a software fix to allow this ie update/ downgrade?? Is it a physical thing or a s…
RE: Beolink 5000 2-way comms problems
in The Workbench · Jun 26, 2007 07:43Hello All, I thought I had better start a new topic as this is being lost in the other listing. the problem I am having with the BL5000 is that it won't receive "feedback" from equipment ie "no contact". I normally use t…
Beolink 5000 & Beocom 6000 sevice manuals?
in The Workbench · Jun 26, 2007 03:39Andy, yes it was from my local dealer about 2 months ago...I was well impressed!!😂 Simon
Beolink 5000 & Beocom 6000 sevice manuals?
in The Workbench · Jun 26, 2007 03:37Anybody?? "Hello, just had another thought on the BL5000 2-way problem. When I press the STATUS button on the BL5000 it correctly gives the source information even though I haven't used it to select the source! Does this…
Beolink 5000 & Beocom 6000 sevice manuals?
in The Workbench · Jun 25, 2007 15:07Andy, do you mean the plastic case and rubber keys for the BC6000 or do you mean the PCB behind the case? I recently updated my BC6000 with a new case and rubber keys for about £25.00 £16.00 including fitting!🙂 Regards,…
Beolink 5000 & Beocom 6000 sevice manuals?
in The Workbench · Jun 25, 2007 14:23Hello, just had another thought on the BL5000 2-way problem. When I press the STATUS button on the BL5000 it correctly gives the source information even though I haven't used it to select the source! Does this mean it IS…
Beolink 5000 & Beocom 6000 sevice manuals?
in The Workbench · Jun 24, 2007 07:15thanks for clarifying that Keith!!
Beolink 5000 & Beocom 6000 sevice manuals?
in The Workbench · Jun 24, 2007 04:49Keith, I seem to remember reading somewhere that the mark2 BC6000 has a different charging voltage. Will this effect my BC using the new board? I will still be using the original charger! What other changes will using th…
Beolink 5000 & Beocom 6000 sevice manuals?
in The Workbench · Jun 23, 2007 10:50Keith, I will order the board from B&O on Monday and will await your instructions! I appriciate your time on this matter, it has been driving me bananas😡 Regards, Simon