Posts by Karnayna
29 total posts20 results
Beogram 4002 stopping suddenly
in General Discussion & Questions · Feb 4, 2020 08:11I had the same problem with one of my 4002s and the culprit was a defective 1TR2 that sometimes, depending on various circumstances (temperature, for example), did not supply the correct voltage or none at all. Soldered …
Beocenter 9500 comes up muted
in Imported Content (Unmapped) · Feb 3, 2020 10:56Dear all, for some days now, when I start my Beocenter 9500 via datalink (pressing <Play> at the record player or tape 2) it sometimes comes up muted. When I press <Mute> everything is fine, but this is not intended beha…
Century turns on but no reaction when pressing keys or remote
in Imported Content (Unmapped) · Sept 22, 2019 11:10Hi! To me this sounds like a bad contact, a cable or soldering. If it is a specific area you have to knock at this might be an indicator where to start checking. Good luck Ingo
Beolink 7000 "No contact" after one day of working
in Imported Content (Unmapped) · Sept 22, 2019 11:06Dear members, I recap-ed my Beolink 7000 and after that it spoke with the Beocenter 9500 as expected. For one day. Now I get this annoying "No contact" message again. What might be the reason for that? I already checked …
Beosound Ouverture CD drive spins without CD only
in General Discussion & Questions · Sept 20, 2019 21:55Dear members, when I press CD on my Ouverture and did not put a CD in I can see the spindle turn and the focus motor do its job. If a CD is in the spindle motor does not turn most of the time 😕. If I take the CD in my h…
Beolink 7000 Movement when switching off?
in General Discussion & Questions · Sept 19, 2019 10:46Dear members, after the usual recap (thanks for guidance!) my Beolink 7000 works as expected. The only issue for me is that I remember faintly that it shall lay down when it switches off after some time and lifts again w…
Clutch wheel on Beocord 6500 / Beocenter 9500
in Imported Content (Unmapped) · Apr 7, 2019 14:50Hi! Die Aussage begründet sich darauf, dass das Zahnrad keine Zähne mehr hat, was für ein Zahnrad ein eher schlechtes Zeichen ist. Der Anschlag für die Kupplung war verbogen, so dass das Zahnrad nicht mehr richtig in Ein…
Clutch wheel on Beocord 6500 / Beocenter 9500
in Imported Content (Unmapped) · Mar 25, 2019 23:10Hi everybody! The clutch wheel in my Beocord 6500 is damaged. It is the same construction as can be found in my Beocenter 9500. The clutch has part #2794135; the wheel has a diameter of 17 cm and 54 teeth. Does anybody k…
Beogram CD 3300: Change supply to 240 V~
in Imported Content (Unmapped) · Nov 28, 2018 11:59Hi! I managed to make my CD 3300 run again and play my CDs, but I'd like to change the supply to 240 V~ instead of the 220 V~ it is originally set to. The schematics show a pin #5 for additional 20 V~, so connecting the …
Beogram CD 3300: Diverse Reparaturen und zwei Fragen (gelöst)
in Imported Content (Unmapped) · Nov 24, 2018 22:43The flat cable was broken just where it comes out of the comnector. I cut 2 mm off the cable, put it back into the connector and the 3300 now plays my CDs as expected! Ingo
Beogram CD 3300: Diverse Reparaturen und zwei Fragen (gelöst)
in Imported Content (Unmapped) · Nov 24, 2018 16:51Yes, the lens moves freely. Without power it is nearly at its lowest position and can't go much further down but can move up quite a long way. Is this normal or should the rest position be near the center? Ingo
Beogram CD 3300: Diverse Reparaturen und zwei Fragen (gelöst)
in Imported Content (Unmapped) · Nov 24, 2018 13:29Well, OK, of course no or bad beam means no focus, but even with a bad beam the lens should at least *try* to focus it, but it doesn't. No movement at all. That's what I am currently stuck with. As I wrote all caps are n…
Beogram CD 3300: Diverse Reparaturen und zwei Fragen (gelöst)
in Imported Content (Unmapped) · Nov 24, 2018 11:59I just saw that the drive motor even starts without a CD. That should not happen as far as i know. The servo seems to tzhink it has already found focus. Can this be a hint? Ingo
Beogram CD 3300: Diverse Reparaturen und zwei Fragen (gelöst)
in Imported Content (Unmapped) · Nov 24, 2018 11:32Thanks for replying. I think the famous laser current capacitor is not relevant for focus detection, but nevertheless it and its colleagues are new and of correct type. It was the first hing I did befor further checking,…
Beogram CD 3300: Diverse Reparaturen und zwei Fragen (gelöst)
in Imported Content (Unmapped) · Nov 23, 2018 10:48Hallo zusammen! Ich hab mich an einen defekten CD 3300 rangemacht und möchte meine Entdeckungen hier kund tun, falls noch jemand einen CD-Spieler haben sollte, der die CDs links herum dreht. Der 220 µF Elko in der -10 V …
Öffnen eines archivierten Threads?
in Imported Content (Unmapped) · Nov 9, 2018 16:44Was für einen Unterschied ein kleines 's' ausmachen kann... Dankeschön Ingo
Öffnen eines archivierten Threads?
in Imported Content (Unmapped) · Nov 9, 2018 14:30Hallo zusammen, B&O-Fan bin ich schon lange und seit ein paar Jahren besitze ich auch zunehmend diese Geräte, vornehmlich reparaturbedürftige Schnäppchen, die ich - auch für Freunde - wieder fit mache. Im Zuge meiner Suc…
Beocenter 9500: Ausschalten startet Motor des CD-Fachs
in Imported Content (Unmapped) · Dec 7, 2017 15:36Thanks for clarification. Ingo
Beocenter 9500: Ausschalten startet Motor des CD-Fachs
in Imported Content (Unmapped) · Dec 7, 2017 14:34Hi Martin, and thanks for the reply. I understand it is normal to close an open door, but the door is already closed because I did not use CD at all in my radio listening session. The motor runs approximately as long as …
Beocenter 9500: Ausschalten startet Motor des CD-Fachs
in Imported Content (Unmapped) · Dec 7, 2017 12:39Hallo zusammen, seit einigen Jahren erfreue ich mich am Beocenter 9500. Trotzdem hatte ich es jetzt für ca ein Jahr außer Betrieb und stelle bei Wiederinbetriebnahme (was für ein Wort!) fest, dass beim Ausschalten des Ge…