Posts by MisterDarlin (archived2)
29 total posts24 results
BeoSound 9000 MKIII CD Scraping Noises On Vertical Floor Stand
in General Discussion & Questions · Apr 22, 2019 02:52[quote user="Bill Briscoe"] Hi, I just pulled out my MKI that's setup for the floor stand (both the BS9000 and the stand are boxed now) and sadly it doesn't have the alt cover you're looking for. If it did I'd gladly sen…
BeoSound 9000 MKIII CD Scraping Noises On Vertical Floor Stand
in General Discussion & Questions · Apr 21, 2019 19:49[quote user="Bill Briscoe"] Hi, I'm glad that worked out! I'm also very embarrassed that I misstated the lack of adjuster screws on the MKIII. The last time I had my MKIII apart I thought there were none, even though I'v…
BeoSound 9000 MKIII CD Scraping Noises On Vertical Floor Stand
in General Discussion & Questions · Apr 21, 2019 17:48[quote user="Bill Briscoe"] Hi, The Mark III version no longer has the screw type adjusters to level the clamper arm like the Mark I had. If you're sure that the part you identified in your first post is what is not leve…
Beosound 9000 Alternate Port Cover (Part 9203) from Floor Stand 2065
in General Discussion & Questions · Apr 14, 2019 21:17Does anyone know where I can purchase part 9203? It is the alternate port cover that came with the Beosound 9000 Floor Stand 2065 (page 4.12 in the service manual).
BeoSound 9000 MKIII CD Scraping Noises On Vertical Floor Stand
in General Discussion & Questions · Apr 14, 2019 20:39Got it, thanks.
BeoSound 9000 MKIII CD Scraping Noises On Vertical Floor Stand
in General Discussion & Questions · Apr 14, 2019 19:46[quote user="9 LEE"] I can save you a lot of time here. If you adjusted the vertical/horizontal settings and it's still scraping - there's a further adjustment to the clamper mechanism which you can fiddle with. However.…
BeoSound 9000 MKIII CD Scraping Noises On Vertical Floor Stand
in General Discussion & Questions · Apr 14, 2019 19:43[quote user="Peter"] To make your MK III respond to Beo4 you have to connect it in A:OPT 1 [/quote] I didn't have any PowerLink speakers hooked up which is why it wasn't responding. I purchased a Speaker Sense Adapter fr…
BeoSound 9000 MKIII CD Scraping Noises On Vertical Floor Stand
in General Discussion & Questions · Apr 14, 2019 19:37[quote user="joeyboygolf"] The carriage has to sit parallel to the bed of the 9000. Over time, a certain amount of droop can occur. The procedure for adjusting this can be found in the service manual. [/quote] Does this …
BeoSound 9000 MKIII CD Scraping Noises On Vertical Floor Stand
in General Discussion & Questions · Mar 25, 2019 16:37[quote user="Peter"] ...plus run TM71 and TM73 on vertical stand before playing CDs [/quote] I will try this but my Beo4 currently cannot connect to my MKIII. Thanks for the tip.
BeoSound 9000 MKIII CD Scraping Noises On Vertical Floor Stand
in General Discussion & Questions · Mar 25, 2019 16:35[quote user="petermc"]Have you changed the orientation settings on the back of the 9000? Refer to pages 7-9 on the guide below. https://www.bang-olufsen.com/~/mediaV3/files/user-guides/BeoSound9000/beosound9000_reference…
BeoSound 9000 MKIII CD Scraping Noises On Vertical Floor Stand
in General Discussion & Questions · Mar 24, 2019 22:52Just setup my MKIII on a vertical floor stand and am experiencing scraping noises on CD slots 1, 3, and 4. CD slots 2, 5 and 6 play just fine. No skipping and no physical damage to CD's occur. If I lean the unit back abo…
BeoSound 9000 Aux Port
in General Discussion & Questions · Mar 19, 2019 12:22[quote user="Beosince98"] The aux connector is for connecting auxiliary equipment to the Beosound 9000, and therefore is input only. You can get output via the power link at the back or the headphone jack. [/quote] Noted…
BeoSound 9000 Aux Port
in General Discussion & Questions · Mar 19, 2019 03:26Is the BeoSound 9000 aux port input or output? Can I use it as a line out with an adapter? Or can I only use the headphone jack?
BeoSound 9000 Audible Volume Buzz
in General Discussion & Questions · Mar 19, 2019 02:46[quote user="Steve at Sounds Heavenly"] Hi, Yes, good cables should resolve this, the noise that you are hearing is the Datalink pulses from pin 6 of the Powerlink cable getting onto the audio channels (pins 2, 3 and 5).…
BeoSound 9000 Floorstand
in General Discussion & Questions · Mar 18, 2019 04:35I'm looking at the diagram from the service manual and I don't understand how there are two height adjustments. I just see 1 height...
BeoSound 9000 Audible Volume Buzz
in General Discussion & Questions · Mar 18, 2019 04:34[quote user="BEOVOX141"] You are listening to the signature sound of the unterminated data transmission on the Powerlink cable. It has been around since the dawn of the LX2800 TV / Beosystem 5500 There are two options Ge…
BeoSound 9000 Audible Volume Buzz
in General Discussion & Questions · Mar 17, 2019 14:29[quote user="PaulGiles"]First thing I would try would be new cables from Steve @soundsheavenly [/quote] I will look into this, thanks. Seller claims the buzzing is normal behavior. This can’t be true right?
BeoSound 9000 Audible Volume Buzz
in General Discussion & Questions · Mar 17, 2019 13:42[quote user="PaulGiles"]We had this once with BV11& BL6000, via TX1&RX1 replaced the link cables for screened RJ45 and problem solved. [/quote] Do you think the volume buzzing issue is on board or just some bad power lin…
BeoSound 9000 Floorstand
in General Discussion & Questions · Mar 17, 2019 13:39[quote user="9 LEE"] There were indeed two 'styles' - but I was actually unaware they had different type numbers! The first version had a polished aluminium 'trim plate' on the circular base. I'd guess these ran for mayb…
BeoSound 9000 Floorstand
in General Discussion & Questions · Mar 17, 2019 13:37[quote user="PaulGiles"]I think the earlier one was a more polished finish whereas the later one was more of a brush effect. (Base) Unsure on model numbers though. [/quote] I believe 2055 is the earlier model and 2065 is…