Posts by alow2004 (archived2)
16 total posts15 results
Beolink active + Beo4 + Arduino to control home lights...
in Imported Content (Unmapped) · Jun 6, 2019 12:58Yes, this is very simple as it is based on a simple 8574 chipset. By the way, if is is for interest for some people, I recently hacked a BEOSOUND5 that was stuck, replaced the mainboard by an Arduino, and managed to deco…
Beolink active + Beo4 + Arduino to control home lights...
in Imported Content (Unmapped) · Jan 29, 2018 21:56Yeah!, do you work on the iOS side only or do you also use some arduino or other stuff (raspberry pi, ?), i am currently working on the blink active setup, but once finished, i will send you what i will discover about th…
Beolink active + Beo4 + Arduino to control home lights...
in Imported Content (Unmapped) · Jan 29, 2018 20:04OK, i have put a little video on youtube to show the actual results... you can check it on: https://www.youtube.com/watch?v=crnG4kiArQU
Beolink active + Beo4 + Arduino to control home lights...
in Imported Content (Unmapped) · Jan 28, 2018 12:18Idea is then to remove the processor board from B&O and replace it completely by an Arduino board...
Beolink active + Beo4 + Arduino to control home lights...
in Imported Content (Unmapped) · Jan 28, 2018 12:17Then the hard work will begin... the idea is to compare (with the arduino serial port as debugger), the code generated be the BEO4, and a same command coming from a Masterlink or Powerlink data, trying to isolate the cod…
Beolink active + Beo4 + Arduino to control home lights...
in Imported Content (Unmapped) · Jan 28, 2018 12:15Now the next step will be to interface with the SDA/SCL signals coming from the IR EYE (Pin 1 and 4) to be able to control also the lights, but maybe to also use the remaining IO ports of the PCF8574 (there are four unus…
Beolink active + Beo4 + Arduino to control home lights...
in Imported Content (Unmapped) · Jan 28, 2018 12:09PART 2: Beoremote_Lookup_Table //Bang&Olufsen Remote code table //This table cross reference codes from the BEO4 and BEORemote One //controllers, some codes are used differently in the two command sets, //those differenc…
Beolink active + Beo4 + Arduino to control home lights...
in Imported Content (Unmapped) · Jan 28, 2018 12:07PART1: Main code #include <Beomote.h> #include <Ethernet.h> #include <Wire.h> #include <SPI.h> #include <Adafruit_Sensor.h> #include <Adafruit_BMP280.h> #include "RGBdriver.h" //Clocked In RGB LED Strip interface -- #def…
Beolink active + Beo4 + Arduino to control home lights...
in Imported Content (Unmapped) · Jan 28, 2018 12:04in fact, this is the part of the project that is already working, i have an arduino mega 2560, connected to a little rgb led driver board, a ethernet card, a temperature/pressure jauge and and IR moment detector. This is…
Beolink active + Beo4 + Arduino to control home lights...
in Imported Content (Unmapped) · Jan 28, 2018 12:04in fact, this is the part of the project that is already working, i have an arduino mega 2560, connected to a little rgb led driver board, a ethernet card, a temperature/pressure jauge and and IR moment detector. This is…
Beolink active + Beo4 + Arduino to control home lights...
in Imported Content (Unmapped) · Jan 27, 2018 20:14ok, i have some code to share, but is it possible to share that on this forum ? how can i do that ?
Beolink active + Beo4 + Arduino to control home lights...
in Imported Content (Unmapped) · Jan 23, 2018 18:20read beomote library, not bromate...
Beolink active + Beo4 + Arduino to control home lights...
in Imported Content (Unmapped) · Jan 23, 2018 18:19hello, this is quit simple for the moment, simply wiring the ir eye pin 7 to the arduino (for test i use an arduino mega 2560, and use the bromate library to decode ir signal. Next step now, i will disconnect b&o process…
Beolink active + Beo4 + Arduino to control home lights...
in Imported Content (Unmapped) · Jan 23, 2018 18:19hello, this is quit simple for the moment, simply wiring the ir eye pin 7 to the arduino (for test i use an arduino mega 2560, and use the bromate library to decode ir signal. Next step now, i will disconnect b&o process…
Beolink active + Beo4 + Arduino to control home lights...
in Imported Content (Unmapped) · Jan 22, 2018 12:34I successfully integrated a little arduino micro board in the Beolink case, i use it to decode some IR code from the BEO4 to turn on or off my lights, keeping the rest of the commands compatible with my Beosound 3200. Is…