Posts by Peel_dk (archived2)
16 total posts14 results
Beosystem 2500 - laserfejl m.m.
in Imported Content (Unmapped) · Mar 18, 2019 11:37Martin: Min tanke var at høre om du vil lave den, så vil jeg komme forbi når du har tid. Jeg har pakket den sammen af samme grund nu. Så kan du selv studere boardet revisionen og kondensatoren, men original det er den. P…
Beosystem 2500 - laserfejl m.m.
in Imported Content (Unmapped) · Mar 17, 2019 11:46Taler vi om C100 eller C2103 - nu er jeg nemlig forvirret fordi der bliver talt om C100 og C2103 fra flere forskellige sider. C100 som er DC stabiliseringen til laseren, den er en Samwhakondensator på 47uF - og den ER or…
Beosystem 2500 - laserfejl m.m.
in Imported Content (Unmapped) · Mar 16, 2019 20:33Jeg har lige fundet ud af at den spiller fint hvis den ligger ned, dvs. hvis hele anlægget ligger på ryggen eller blot er vippet 45grader baglæns. Men står det op lodret - ja jå "raller". Sært. Der må være en mekanisk us…
Beosystem 2500 - laserfejl m.m.
in Imported Content (Unmapped) · Mar 16, 2019 17:24Yes, I know. It is designet for SMPS, and I have only them in stock so I use them for everything. Can't get better quality, no reason to have other types. If you experience problems with them, then you have a poorly desi…
Beosystem 2500 - laserfejl m.m.
in Imported Content (Unmapped) · Mar 16, 2019 10:37Ok, great. The FR and FM are the same capacitor, FM are just for only 2000-7000hours where FR are for 5000-10.000hours. But anyway, it it not that problem i have here. The spindels runs backwards at full speed. I also no…
Beosystem 2500 - laserfejl m.m.
in Imported Content (Unmapped) · Mar 15, 2019 21:37Hmm, it sounds very strange. I am an electronics technician, and the Panasonic FR is the best quality 105° low-esr capacitor you can get. The original cap. is a low quality SAMHWA capacitor like almost the rest of the ca…
Beosystem 2500 - laserfejl m.m.
in Imported Content (Unmapped) · Mar 15, 2019 18:25Hi Ok, thank you. I replaced it with a Panasonic FR capacitor, and the laserarm is steady and it seems to have cleared the problem. BUT not completely: it makes a rattle sound, turns a few times around, makes a rattle so…
Beosystem 2500 - laserfejl m.m.
in Imported Content (Unmapped) · Mar 15, 2019 13:54Det er den kurvede jeg har. Den sidder under spindlen og drejer, til venstre, om sin egen aksel. Jeg har målt lytterne efter på CD boardet, og der er ikke nogen der umiddelbart fejler noget (værdi og ESR værdi).
Skidt stil
in Imported Content (Unmapped) · Mar 14, 2019 19:47Jeg har været ude for det samme med folk der indleverer udstyr til Hifibutikken - utallige gange. Så mange at jeg nu er 100% sikker på de gør det med vilje: de VED at de ikke kan reparere det fordi det skal laves på komp…
Beosystem 2500 - laserfejl m.m.
in Imported Content (Unmapped) · Mar 14, 2019 19:30Hej alle Jeg har et Beosystem 2500 stående der ikke vil læse CD. Den har lidt sit eget liv, laseren vipper op og ned, spindlen kører lidt rundt, og "ryster" mens den kører baglæns og kan pludselig finde på at køre på ful…
Beolab 4000 questions - foam rot
in General Discussion & Questions · Apr 9, 2017 00:32Just some pictures of the problem you described. I have repaired several of them during the years, it is a very serious problem to a good and very universal speaker! Regards, Peter Andersen www.peel.dk
Beomaster 6500 - strange behaviour....
in Imported Content (Unmapped) · Nov 12, 2016 20:21Thank you very much - I will appreciate that! Can you sent it on email to me? Sent me a PM. And you are right: it was an activation of the option 0 that was the problem. I have replaced the uP, eprom and NVram before but…
Beomaster 6500 - strange behaviour....
in Imported Content (Unmapped) · Oct 1, 2016 15:06Is there really nobody out there that can help me with a bin/hex file of the EPROM in the 6500? Peter
Beomaster 6500 - strange behaviour....
in Imported Content (Unmapped) · Sept 28, 2016 22:44Hi I have a Beomaster 6500 on the table with a quite strange problem. It came in with defective uP. After replacing it, performing a reset - and replacing the standard electrolytes capacitors around, it was working, no p…