Posts by JohnMoore (archived2)
14 total posts13 results
BeoLab 1 problem.
in Imported Content (Unmapped) · Nov 3, 2016 11:28Sihariddh, it has been a long time since I replaced the 4A slow burn fuse but so far so good and I hope this e mail does not jinx anything with the Beolab 1. I downloaded the dismantling brochure from the net but i,m not…
BeoLab 1 problem.
in Imported Content (Unmapped) · Feb 4, 2015 17:27One last point....B&O came back yesterday and said that they would be able to repair the BeoLab on a chassis level. If I get it to a workshop in Malta , B&O Italy would advise them how to strip it down, then that worksho…
BeoLab 1 problem.
in Imported Content (Unmapped) · Feb 4, 2015 17:19I have replaced the 4A slow blow fuse, connected everything up and the speaker works! Goes from standby to green and stays there. Have run it all afternoon. Perhaps the problem will come back because that fuse protects s…
BeoLab 1 problem.
in Imported Content (Unmapped) · Jan 31, 2015 14:59Thanks for all the advice. I have spent so much over the last year repairing B&O equipment (Beosound 9000, 2 Beolab 4000's which failed within 6 months of each other) that I have to conclude that my B&O units are failing…
BeoLab 1 problem.
in Imported Content (Unmapped) · Jan 30, 2015 12:47Beobuddy a few days ago sent a picture of the circuitry and my BL1 is exactly the same inside. On that pic is a big circuit panel at the top, then a copper wired whatever in the middle then a smaller panel at the bottom.…
BeoLab 1 problem.
in Imported Content (Unmapped) · Jan 29, 2015 14:11I have checked the individual loudspeakers visually and they all seem ok. I managed to flip over the cooling profile and set it on its back to have a look at the boards/amp to see if anything obvious. Several posts ago I…
BeoLab 1 problem.
in Imported Content (Unmapped) · Jan 28, 2015 10:37Thanks tompa, that is very helpful and i'll check the connections as suggested.
BeoLab 1 problem.
in Imported Content (Unmapped) · Jan 27, 2015 16:08Dear Beobuddy, it doesn't look familiar because I cannot get the aluminium cooling profile off...I removed all the screws and the two screws at the bottom but it won't lift off and i'm reticent to use a screwdriver to he…
BeoLab 1 problem.
in Imported Content (Unmapped) · Jan 21, 2015 14:20Thanks for the suggestion. The tweeters looked fine but I switched them round as suggested but it made no difference. Same problem....one speaker fine but the other is red with the standby LED but when sound flows it goe…
BeoLab 1 problem.
in Imported Content (Unmapped) · Jan 20, 2015 14:00I have downloaded a brochure on how to dismantle the BL1. However, when you get the front panels off it is clear that the problem is in the electronics and around the LED which only becomes clear when the base is off. So…
BeoLab 1 problem.
in Imported Content (Unmapped) · Jan 16, 2015 21:57Thanks. I'll try that. In the meantime I had a response from Detron in the Netherlands who handle vintage repairs and fixed my Beosound 9000 at a huge cost but have said that they cannot fix a Beolab 1 speaker cus no spa…
BeoLab 1 problem.
in Imported Content (Unmapped) · Jan 16, 2015 14:03I have checked the power and changed the cables....one thing I did not see before is that the standby light is actually on but very very dim so it is very difficult to see.It is not bright like the other speaker and does…
BeoLab 1 problem.
in Imported Content (Unmapped) · Jan 15, 2015 16:11Can anyone help advise me. The indicator light on my BeoLab 1 will not come on. I have rechecked the power connection a hundred times but the power indicator will not come on and the speaker is dead. I cannot take it to …