Posts by ktroyh (archived2)
26 total posts20 results
Beogram 8002 stylus arm not behaving / returning properly
in Imported Content (Unmapped) · Dec 31, 2014 02:22Hello everyone, I recently acquired a Beogram 8002. The initial repairs were covered on another thread and the table was working normally but today things changed. Actually I guess everything wasn't perfect. The first ti…
Beogram 8002 stylus arm not behaving / returning properly
in BeoGram · Dec 29, 2014 05:51I recently acquired a Beogram 8002. The initial repairs were covered on another thread and the table was working normally but today things changed. Actually I guess everything wasn't perfect. The first time I cued the pl…
beogram 8002 wire color positions for din board
in BeoGram · Dec 29, 2014 05:34So the connections are now done and the channels are correct and working. On to the next issues. Thanks for everyone help!! Troy
beogram 8002 wire color positions for din board
in BeoGram · Dec 21, 2014 22:32I'm not going to pull the relay because that may cause more problems than it solves. All things being equal I have a 50/50 chance at getting it right and after looking at my original pictures they wire positions improved…
beogram 8002 wire color positions for din board
in BeoGram · Dec 21, 2014 20:18I agree the only question I have is which is right and left channel between your whites? I did a continuity check between the din 3 and the board and din 5 and the board and got continuity between din 3 and board 2 and 4…
beogram 8002 wire color positions for din board
in BeoGram · Dec 21, 2014 20:18I agree the only question I have is which is right and left channel between your whites? I did a continuity check between the din 3 and the board and din 5 and the board and got continuity between din 3 and board 2 and 4…
beogram 8002 wire color positions for din board
in BeoGram · Dec 21, 2014 18:09It appears my green and blue may be your uninsulated speaker grounds. My red and white must be the the right and left channel speakers where yours are both white. My uninsulated wire must be your blue which is??
beogram 8002 wire color positions for din board
in BeoGram · Dec 21, 2014 17:01I can see our wire colors are not the same at all. Ant thoughts?
beogram 8002 wire color positions for din board
in BeoGram · Dec 21, 2014 00:16Hello all, I opened the case of my 8002 turntable today to align the pickup arm and found the scene below. Can anyone tell me the wire color positions for re-soldering this din board?? Many thanks, Troy
Mystery spring beogram 8002 turntable
in Imported Content (Unmapped) · Dec 20, 2014 20:00Thank you Sonavor, It is likely that is the spring because the deck was off the table. Troy
Mystery spring beogram 8002 turntable
in Imported Content (Unmapped) · Dec 20, 2014 19:13Can you link that thread? Troy
Mystery spring beogram 8002 turntable
in Imported Content (Unmapped) · Dec 20, 2014 18:41Lee, Thank you, Troy
Mystery spring beogram 8002 turntable
in Imported Content (Unmapped) · Dec 20, 2014 18:12Lee, Can you tell me is it the #507 or 525?
Mystery spring beogram 8002 turntable
in Imported Content (Unmapped) · Dec 20, 2014 18:07Perhaps that is why the arm is sitting low. I am a proud new owner of this table and there a few things that have been done by the previous owner that need to be remedied. At least this part is there as a clue. I fear th…
Beogram 8002
in General Discussion & Questions · Dec 20, 2014 17:54I sent my requirements to my 3M tape supplier and he recommended VHB tape. I used RP26. It might be a bit thin for the under the deck trim. I used it and both locations with excellent results on the hige and good results…
8002 turntable feet
in Imported Content (Unmapped) · Dec 20, 2014 16:26I could use those and probably will if I cannot find originals. My problem is that I am quite anal and it would drive me nuts. I took a hot glue gun and fashioned a replacement and it is working quite well. Troy
Mystery spring beogram 8002 turntable
in Imported Content (Unmapped) · Dec 20, 2014 16:21When reassembling my turntable I found a small spring floating in the case. I searched the manual and could not find one that resembled it can anyone help? Thanks, Troy
beogram 8002 din board wire position colors
in Imported Content (Unmapped) · Dec 20, 2014 15:39Hello all, I opened the case of my 8002 turntable today to align the pickup arm and found the scene below. Can anyone tell me the wire color positions for re-soldering this din board?? Many thanks, Troy
Beogram 8002 parting
in BeoGram · Dec 20, 2014 15:14I am in need of the feet for the bottom of the 8002 turntable. without them my cover does some funky stuff. Does the table your parting have them? My remainingfeet are a hard plastic button though the manual says rubber.…
8002 turntable feet
in Imported Content (Unmapped) · Dec 20, 2014 05:01Hello to all in Beoworld, I was lucky enough to pick a pretty nice 8002 turntable the other day and began setting it straight right away. The aluminum door was easy enough after my 3m tape supplier hooked me up with the …