Posts by Beofan58 (archived2)
33 total posts23 results
Beogram 8002. Tonearm won't lift
in BeoGram · Aug 16, 2015 22:56Thank you for your reply. It turned out to be some bad solder connections on the controller board. All adjusted and working perfectly. Caps & components are all fine. Regards, larry
Beogram 8002. Tonearm won't lift
in BeoGram · Aug 5, 2015 21:50I just acquired a beautiful 8002 and have an intermittent issue where the tone arm fails to lift when pressing stop, pause, or at the end of the record. When you press the forward key it will drag the stylus along with t…
Speakerlink 4-pin cables
in Imported Content (Unmapped) · Jun 26, 2015 05:56Thanks Dave, Very good source! I saw the Sounds Heavenly cables but they are a little on the rich side. However, another BW member contacted me with a 10m pair (NOS) that I bought and they'll be here in a few days, so pr…
Speakerlink 4-pin cables
in Imported Content (Unmapped) · Jun 24, 2015 01:29I am looking for a pair of speakerlink compatible 4 pin cables to hook up my Pentas to a BM5500. 5M or longer. If you have any you'd like to sell me drop me a message (I'm in California) Thank you, Larry
Wanted - Beomaster 8000 programming lid hinge.
in Imported Content (Unmapped) · Mar 25, 2015 01:54Part no longer needed. (Was able to repair w existing parts). Thanks
Beomaster 2400 & Beogram 8000, PH to FM switching issue
in General Discussion & Questions · Mar 22, 2015 18:33Martin, it is an original cable. I unscrewed the two contacts and it's working perfectly! Problem solved!! Thanks to Chris & Dave as well for the wonderful suggestions! Best Regards, larry
Beomaster 2400 & Beogram 8000, PH to FM switching issue
in General Discussion & Questions · Mar 21, 2015 17:21Chris, You wouldn't happen to know where I might find an adapter, which has 7 pins/holes but only the audio connected (pins 2,3,5), would you? Or would it have to be made up as a custom? It would be pretty sweet to be ab…
Beomaster 2400 & Beogram 8000, PH to FM switching issue
in General Discussion & Questions · Mar 21, 2015 17:02Hi Chris, Thank you, that's a big help! That explains why I haven't been able to get either my 4004 or the 8000 Beogram to work properly through the 2400. (I didn't think I'd have two 2400's with the identical issue)! I …
Beomaster 2400 volume jumps to full blast
in General Discussion & Questions · Mar 19, 2015 21:41Hi Martin, As usual, thank you for your comprehensive reply, learning, and probable causes for this condition. I love the 2400's and have had several now, with varying states of electronic and/or cosmetic issues. It's pr…
Beomaster 2400 volume jumps to full blast
in General Discussion & Questions · Mar 19, 2015 19:21While I'm at it, the other problem with this particular Beomaster 2400 is that the volume control sticks, and then when I finally get it to respond it jumps to full volume (either w remote or by the touch control. (My ho…
Beomaster 2400 & Beogram 8000, PH to FM switching issue
in General Discussion & Questions · Mar 19, 2015 18:49There was a previous thread on this topic but it doesn't fully address my issue, which is as follows: I am trying to hook my Beogram 8000 up to a Beomaster 2400. However, the moment I plug in the DIN into the Phono input…
Beomaster 6000 - non-working. For parts or repair
in Imported Content (Unmapped) · Mar 11, 2015 19:48I have a Beomaster 6000 with the ever popular condition of shutting itself off after a few seconds. I'd like to get $100 out of it if anyone has a need for a donor or parts machine, or up for a project. The overall condi…
RL Speaker Wall Mounts - pair
in Imported Content (Unmapped) · Mar 11, 2015 04:37Dave, Thank you for the suggestions. I just found and bought a pair! Regards, Larry
RL Speaker Wall Mounts - pair
in Imported Content (Unmapped) · Mar 7, 2015 18:25I'm looking for a pair of factory wall mounts to hang my RL60.2's. Shipping to California Thank you! Larry
Beogram 8000 tone arm not dropping
in BeoGram · Mar 5, 2015 09:47Martin, Perfect, I knew there had to be a trick! I had no idea that little piece of wire is what holds the entire suspension... Simple, yet ingenious (of course)! thank you, larry
Wanted - Beomaster 8000 programming lid hinge.
in Imported Content (Unmapped) · Mar 5, 2015 00:17fed Ex struck again by dropping what was an immaculate Beomaster 8000 in transit. The hinge for the programming section lid is broken and a few fins were bent in the rear corner).... Which I hope to straighten. I am look…
Beogram 8000 tone arm not dropping
in BeoGram · Mar 4, 2015 21:33Hi Dave, You guys are so good, I don't have to hang around too long to solve my Beo problems! By the way, what is supposed to keep those W shaped wire pieces under the chassis in place that the suspension hooks grab on t…
Beogram 8000 tone arm not dropping
in BeoGram · Mar 3, 2015 19:42Martin, Thank you. I left the original belt alone. Seems fine. Best Regards, Larry
Beogram 8000 tone arm not dropping
in BeoGram · Mar 3, 2015 15:24I just purchased a beautiful beogram 8000 from the original owner that had stored it since new. it worked flawlessly initially but after some further testing the tone arm moves into position but won't drop on its own (it…
Beogram 8000 tone arm not dropping
in General Discussion & Questions · Mar 3, 2015 15:13I just purchased a Beogram 8000 that's nearly new old stock from the original owner that had stored, and never used it since new. it worked flawlessly initially but after a short while the tone arm won't drop. The servo …