Posts by Agent00soul (archived2)
17 total posts14 results
Beogram 4000 no power
in Imported Content (Unmapped) · May 14, 2013 13:08Shouldn't it be the other way 'round?
Beolit slimstyle speaker
in Imported Content (Unmapped) · May 12, 2013 09:15Thanks Martin. With the magnet off (see pictures below) it is clear that the inside of the coil has rubbed against the magnet center. This has caused burr in the aluminum. I wonder if this can be removed without damaging…
Beolit slimstyle speaker
in Imported Content (Unmapped) · May 11, 2013 22:41OK, so maybe it isn't worth the effort trying to fix it then. I have two Beolit 600s with working speakers already. Anyway, I now have found that the magnet and the rear steel plate can be rotated and moved sideways as a…
Beolit slimstyle speaker
in Imported Content (Unmapped) · May 11, 2013 21:53Hi Martin. I examined the magnet very carefully and it doesn't look unglued. But maybe you are right after all. I'll make another attempt at pushing it. /Jörgen
Beogram 1202 - no signal, no sound ?
in Imported Content (Unmapped) · May 11, 2013 19:35You set the knob to "0" and then turn the counterweight until the tonearm balances in mid-air. Then you set the knob to the desired needle pressure.
Beolit slimstyle speaker
in Imported Content (Unmapped) · May 11, 2013 19:29I won a Beolit 505 that I bidded for mainly to get the red panels, an undamaged antenna (with correct top) and possibly other parts. The radio was advertised as non-functional but when I turn it on, it does actually play…
Replacing trimmers?
in Imported Content (Unmapped) · Oct 18, 2012 16:19OK, I looked up the Piher closed cermet trimmers. These are available with 5 x 10 mm pinout at very decent prices. That looks to me like the best choice. In the drawer I only have cermets with 5 x 2.5 mm pinout, so I'll …
Replacing trimmers?
in Imported Content (Unmapped) · Oct 18, 2012 13:01[quote user="Dillen"] Depends on the type originally fitted, but in most cases yes. Martin [/quote] OK, are there recommended types for this, or should ordinary open carbon trimmers (like in original) be used?
Beovox 1600 Mexico
in Imported Content (Unmapped) · Oct 18, 2012 11:51[quote user="Søren Mexico"] [quote user="Leslie"] The speakers look great Soren but the word "bagger" was just funny to read🙂 [/quote] They not only look great, I have never imagined that a pair of 2 way small speakers …
Replacing trimmers?
in Imported Content (Unmapped) · Oct 18, 2012 11:04When recapping 70's Beomasters, is it recommended to replace the trimmer potentiometers at the same time?
Opening a Beovox S45?
in Imported Content (Unmapped) · Oct 14, 2012 18:22Thanks Martin. I managed to get it off without damage to the front or the aluminum edge. A steel ruler is your friend. The crossover has three 16 uF/40V capacitors. Is it a good idea to use the bipolar electrolytics, tha…
Opening a Beovox S45?
in Imported Content (Unmapped) · Oct 14, 2012 12:01So you start by prying the front off? Any special technique for that? How is it held in place?
Opening a Beovox S45?
in Imported Content (Unmapped) · Oct 13, 2012 20:31Hi all. I just received a pair of Beovox S45 (mark I). I'm going to give them a checkup and cleaning etc. So how do you open them up with the least risk of damage? Another question: Where can you buy the female DIN louds…
CX100 replacement drives
in Imported Content (Unmapped) · Sept 10, 2012 10:31It takes much more than 10 minutes to carefully remove the dust cap, to source a new dust cap and to glue the new one in place. Additionally, when removing the dust cap, there is a high likelihood that debris (paper from…