Posts by KCkid (archived)
18 total posts16 results
Master control panel 5000 no transmission to Beomaster 5000
in North America · Mar 28, 2010 15:07[quote user="tournedos"] Don't despair - you need to use SHIFT+RESET to toggle loudness (and SOUND+STORE thereafter if you want the current setting to stay as a power-on default, it stores current volume etc. as well). T…
Master control panel 5000 no transmission to Beomaster 5000
in North America · Mar 27, 2010 21:55[quote user="Medogsfat"] I agree with Mika, are you sure it is a Beomaster 5000 you have? If it can be controlled with a Beolink 1000 It sounds like you have a Beomaster 5500. If it IS a Beomaster 5500 then a MCP 5000 wo…
Master control panel 5000 no transmission to Beomaster 5000
in North America · Mar 27, 2010 16:12[quote user="elephant"] so the BM5000 is receiving the IR and behaving itself seems you need to focus on the MCP after checking the obvious -- batteries -- you should search the board for "MCP" -- there have been quite a…
Master control panel 5000 no transmission to Beomaster 5000
in North America · Mar 27, 2010 13:38Hi just bought a master control 5000 off Ebay to control my 5000 system and it is not comunicating with the beomaster 5000. Question is there a set up i need to perform before they will link up? I do not have the owners …
Beogram CD50 tray will not open
in North America · Mar 21, 2010 16:55I have a tube of white lithium greese and agree and will use it on the plastic gears i have cleaned all of the brass with gun solvent and dried and then cleaned with rubbing alk. I then used a high quality gun oil on the…
Beogram CD50 tray will not open
in North America · Mar 21, 2010 12:55[quote user="tournedos"] This comes out from fading memory, but that's not where the belt is supposed to go. In your photo, straight above the grooved pulley, you can faintly see a brass pulley - that is the tray motor a…
Beogram CD50 tray will not open
in North America · Mar 21, 2010 09:56[quote user="Dillen"] It lifts straight up and off. But you MUST mark the tray and gear together. Martin [/quote] Thanks Martin, it did finally come off. I used an allen wrench as a pry bar gently pushing equally on thre…
Beogram CD50 tray will not open
in North America · Mar 21, 2010 00:05Indeed it does screw off counter clock wise. I am now trying to remove the large gear wheel by wiggling it and pulling strait up at the same time but it does not want to release.
Beogram CD50 tray will not open
in North America · Mar 20, 2010 23:32[quote user="Dillen"] There are two set screws and then it screws off. Make sure to mark EVERYTHING, some of the gears are put together in a special way (coded) but bears no markings of this, and they need to be put back…
Beogram CD50 tray will not open
in North America · Mar 20, 2010 17:19After a long delay i have a snow day on the first day of spring so decided to finish with the belt install. I have the tray up and out of the way and have decided the large wheel has to be removed along with one smaller …
Beogram CD50 tray will not open
in North America · Dec 10, 2009 15:22I had to losen the arm and the actuator plate on the front side to lower the door enough to access and remove the screw. After i had the door open the large gear wheel turned freely and I opened the tray by hand ,the bel…
Beogram CD50 tray will not open
in North America · Dec 8, 2009 20:38I have the cover off and the inside is spotless I cannot belive how clean it is compared to other responses of how dirty theirs where. Maybe it has been serviced in the recent past but it just looks like it has been in a…
Beogram CD50 tray will not open
in North America · Dec 8, 2009 16:14Ah, i should have waited for a reply, ok i understand it now. Thanks for the heads up on that. Thanks! Glad to be here.
Beogram CD50 tray will not open
in North America · Dec 8, 2009 16:07Tournedos, thanks for the quick reply. That's what it looked like on the cord but i wanted to check first. Good pointer on the gears i will magic mark and index point and that gives me an idea to on the pictures ,i will …
Beogram CD50 tray will not open
in North America · Dec 8, 2009 15:23I have the back two screws removed, on the bottom it says move them up and retighten??? also looks like i have to remove the din cord from the rear to lift the top up. It does pull straight out or is it permantly bonded …
Beogram CD50 tray will not open
in North America · Dec 8, 2009 14:02Hi everyone I am a firts time poster and first would like to say i have the B&O 9000 and just love it. I was wanting to upgrade from my RX turntable to a beogram 5500 table I found on the local Kansas City Craig's list a…