Posts by Jacob Terp Christensen
37 total posts32 results
BeoLab 3 - Din/RCA cable, question about wiring
in BeoLab · May 13, 2026 13:32Alright, I will disconnect the pins. Thanks!
BeoLab 3 - Din/RCA cable, question about wiring
in BeoLab · May 13, 2026 11:14So I just made a couple of cables for my BeoLab 3 as I want them connected to a volume controlled pre-out amp. I made two of the marked cables in this diagram. I don't know if this is correct, or I should just have made …
Beolab 3 with PC - Best solution?
in BeoLab · May 8, 2026 21:38So I just acquired a set of BL3's that I want to use with my PC. I've seen post with people suggesting the cable from Sounds Heavenly, but a local supplier makes an adaptor that also has a USB trigger. So what is the bes…
BeoPlay A9 MK2 - Overheating, amber blinking
in BeoPlay · Mar 27, 2026 07:44I purchased this BeoPlay A9 MK2 for cheap, as it had an error with amber blinking lights at startup. I have measured the drivers, and midrange and tweeters measure within spec, comparing to the MK3 service manual. The wo…
Beolab 14/BeoPlay S8 - Amp not working
in BeoLab · Feb 25, 2025 11:07Any update on this? My S8 is still dead after replacing the same IC as Jonathan, and I don't know what to check for.
Beolab 14 Sub - IC identification needed !
in BeoLab · Feb 14, 2025 17:52Thanks, I'll watch the thread to see if any new info is shared. Although I do not get any hiss or anything, it might be of value.
Beolab 14 Sub - IC identification needed !
in BeoLab · Feb 14, 2025 17:29Sadly not, I haven't looked into it yet. Can you link the post? Would be interesting to see if it is the same problem.
Beolab 14 Sub - IC identification needed !
in BeoLab · Jan 28, 2025 20:03No, I haven't tried the green button, and I don't know what it is for. I'm not that interested in testing with live 230v on exposed capacitors, but it might be necessary to see where it goes wrong.
Beolab 14 Sub - IC identification needed !
in BeoLab · Jan 28, 2025 19:52Hey, did you get time to look at it? I finally got time to test mine, and as yours, I get absolutely nothing. It is completely dead, and I am wondering if a smd fuse might have blown on the power supply board.
Beolab 14 Sub - IC identification needed !
in BeoLab · Jan 24, 2025 09:49Just an update, Got the other IC soldered, and the sub assembled. Will be testing it today or tomorrow. Hopefully it won't explode, in which case, you wont hear from me again :D
Beolab 14 Sub - IC identification needed !
in BeoLab · Jan 20, 2025 12:23Thanks! Did you get yours to work?
Beolab 14 Sub - IC identification needed !
in BeoLab · Jan 20, 2025 12:06My S8 is the earlier model, which should be identical to the 14's. Do you have pictures of the mounting on yours? I believe they use the same ICEpower module and power supply.
Beolab 14 Sub - IC identification needed !
in BeoLab · Jan 20, 2025 11:44I soldered the new IC, but when installing the boards, I managed to rip off a bi-amp IC, so I am now waiting for a replacement for that. When installing the boards, they have to be forced down on each side of this plasti…
Beolab 14 Sub - IC identification needed !
in BeoLab · Jan 17, 2025 11:14I don't think it should be necessary to press a button. The button might be needed for service.
Beolab 14 Sub - IC identification needed !
in BeoLab · Jan 16, 2025 19:49Sounds like a good idea. I will try and see if I can get mine working in the weekend.
Beolab 14 Sub - IC identification needed !
in BeoLab · Jan 16, 2025 19:32Okay, I never really noticed the light, but according to this thread, it should show something when receiving a signal. /forum/general-discussion-and-questions/activity-led-on-beolab-14
Beolab 14 Sub - IC identification needed !
in BeoLab · Jan 16, 2025 18:55Hey Jonathan, No I haven't received the IC yet, but hopefully it will arrive tomorrow, so I can fit it and assembly it in the weekend. The connectors in the middle of the board (marked) are unused, I guess they are used …
Beolab 14 Sub - IC identification needed !
in BeoLab · Jan 9, 2025 07:35Yeah it is on the side of the icepower pcb.
Beolab 14 Sub - IC identification needed !
in BeoLab · Jan 8, 2025 21:41Thanks for the pictures! I could finally decipher the text on top of the diode :) The flex cable goes to the ICEpower module, see pic.
Beolab 14 Sub - IC identification needed !
in BeoLab · Jan 7, 2025 20:46Thanks Jonny! I've ordered the IC chip, so I hope the problem is "as easy" as yours! Would love some pictures when you get it back.