Posts by citronix
27 total posts21 results
Beocord 9000 tape calibration never stops
in BeoCord · Feb 5, 2024 19:18Well - I made it so far, that when I disconnetc the P26 - the 8 pin plug on PCB 11 - the DAC, the autocalibration turns of after been engaged for about 10 seconds - which seems correct. But why - I still dont know I have…
Beocord 9000 tape calibration never stops
in BeoCord · Jan 2, 2024 10:57Everything seems to be working except the auto tape calibration. It runs endless until I press stop. It shoud take 10-20 seconds, not 45 minuts, I have read some old posts regarding the subject, but not found any answers…
Beocord not rewinding or forwarding - here is a solution
in BeoCord · Nov 7, 2023 17:05Thanks a LOT - been trying to find the fault on my Beocord 5500 for ages - but coudnt until i red your post
Beosound Overture/4000 SP/did out??
in Imported Content (Unmapped) · Jan 17, 2022 08:18Is there a way to extract the SP/DIF signal from the Beosound Overture/2300/4000 to an external DAC? Cheers Michael/DK
Beomaster 5500 timer stuck
in Imported Content (Unmapped) · Nov 24, 2020 18:16following the sequense in the users guide im simply not able to erase the previous settings. Anyone who has a fix? Cheers/Michael DK
Renovation of Mmc2, what to choose?
in BeoGram · Mar 15, 2017 10:38I just receiver a restored MMC 4 with Shibata stylus and alu cantilever from tonabnehmerservice.de At a pricetag of 255 euro Im very pleased. Lots of low end, a Well defined mid and top without any annoying harsh sounds.
Beogram 1000 - drive belt needed
in Imported Content (Unmapped) · Aug 11, 2016 07:09And whereabouts Do i find Axel, sinde i have The same problem
Beogram 6002 belt dimentions
in BeoGram · Aug 10, 2016 15:31does anybody know the belt dimentions of the small belt driving the tone arm on the Beogram 6002?i I tried with a random belt, but it's a little too tight. The manual does not state the dimentions, only a part number tha…
Beogram TX/6002 arm moving too slow
in BeoGram · Oct 16, 2015 12:44A small adjustment of the "second" arm, towards center, did the trick - its not 100% parralel to the tonearm anymore, but its hardly visible, and the unit is playing as expected - thanks for all the input.
Beogram TX/6002 arm moving too slow
in BeoGram · Oct 16, 2015 12:14further research has revield, that if I manually turn the tonearm towardss the center, (thaht is I push the tonearm all the way to the left, so it touches the other arm) the whole carriage is mooving too :-) Whitch must …
Beogram TX/6002 arm moving too slow
in BeoGram · Oct 16, 2015 11:51local - its not original, and as far as I remember its diameter is 100 mm and wit 1,8 mm - its rather tight - could that make a difference?
Beogram TX/6002 arm moving too slow
in BeoGram · Oct 16, 2015 11:44I have opend the unit now, should there be visible light at the LDR?
Beogram TX/6002 arm moving too slow
in BeoGram · Oct 16, 2015 11:43I do not know, the old belt was broken :-(
Beogram TX/6002 arm moving too slow
in BeoGram · Oct 16, 2015 11:13Sounds reasoanble - but what shall I look fore - the light is ON on the tone arm. I suspect that LDR is short for Light Dependent Resistor - but thats as far as I get Bad tracking, either the lamp or the LDR or both.
Beogram TX/6002 arm moving too slow
in BeoGram · Oct 16, 2015 10:48I have clened everything, and there is no bumps or dirt on the spindel - it would also have been my first thought. When pressing the left or right button the arm moves freely, without haning anywhere . maybe the spindel …
Beogram TX/6002 arm moving too slow
in BeoGram · Oct 16, 2015 10:12When I hit "play" everything works as intended, but the tangential arm itself is moving too slow , After playing 1/3 of a record, the pickup arm is angled towards the center og of the record, maybe 10 to 15 degrees!!! I …
Beogram CD 4500 spinning issues
in Imported Content (Unmapped) · Sept 10, 2015 13:13Thanks a lot - I cleaned it up once more, and magic happend. It does play now, not everytime, but it seems that it only needs tro warm up a little, then its playing. Which in my world could link to the capacitor issue me…
Beomaster 4500
in Imported Content (Unmapped) · Sept 6, 2015 08:51IDO agree - its sutch a beautifulsystem. I just got myself a compleate one and first thing is to do the glass - how do you rmove the old without damaging the glass??
Beomaster 4500
in Imported Content (Unmapped) · Sept 6, 2015 08:51IDO agree - its sutch a beautifulsystem. I just got myself a compleate one and first thing is to do the glass - how do you rmove the old without damaging the glass??