Posts by dave_n_s
69 total posts54 results
How to add / use additional functions to Beo4 - manual instructions not helping
in BeoRemote · Feb 18, 2025 17:10@Guy, SOUND > GO gets it into Balance mode and pressing Vol up or down changes the balance. For completeness if anyone else finds this discussion, Vol up & down adjust Bass, Treble in the same way. An interesting voyage …
How to add / use additional functions to Beo4 - manual instructions not helping
in BeoRemote · Feb 18, 2025 15:59Progress....nearly there! Thank you both @Millemis, I found A.SETUP, although to do so, I found it by selecting another source (not CD) before pressing standby+list @Guy, my Beo4 indeed has an AV button in the middle of …
How to add / use additional functions to Beo4 - manual instructions not helping
in BeoRemote · Feb 17, 2025 23:58While I fix my Beomaster 5500 Master Control Panel, I still have a Beo4, which works for the basics, I'd appreciate some help adding and using some basic functions on the Beo4. It's not following the manual - step one sa…
Beomaster 5500 Master Control - rotary control only works in one direction
in BeoMaster · Feb 17, 2025 23:36After many years of faithful service, my master control panel only works in one direction (turning anti-clockwise). I realise it's optical, but that bit is clearly working, correct? Any pointers on how to troubleshoot wo…
Beogram 8002 Dust cover alignment
in General Discussion & Questions · Dec 13, 2021 15:38super documents. thank you. And of course I have read them! what thickness (not width) of VBR tape do you use please?
Beogram 8002 Dust cover alignment
in General Discussion & Questions · Dec 13, 2021 05:57sonavor, thank you very much. I'll check the points you noted. Is there any possibility that the top and side of the control module could be out of alignment?
Beogram 8002 Dust cover alignment
in General Discussion & Questions · Dec 12, 2021 21:43I have an 8002 that has just one annoying flaw, the front right edge of the dust cover just contacts the controls area as it is closing. On earlier models, that alignment is fixed by loosening the screws that hold the wh…
Beocenter 2300 / 2500 door string / wire reinstallation.
in General Discussion & Questions · Oct 22, 2021 02:15I'm trying to get a Beocenter 2300 ready for some new doors. It came with no doors and worked fine for years, but I think it would like some doors. I've flipped the two black side panels off and can see all the string ro…
Beogram 3400 Turn button operative, no other controls operative
in BeoGram · Jan 12, 2020 19:12Yes, all the joints on the control panel board and all the connectors, including the power transistor socket, on the main board.
Beogram 3400 Turn button operative, no other controls operative
in BeoGram · Jan 4, 2020 04:16Am I getting a broad hint that these aren't economic repairs except for really simple stuff? That's where I'm heading
Beogram 3400 Turn button operative, no other controls operative
in BeoGram · Dec 22, 2019 15:50Martin, Start button cleaned, resistance v low when operated, measured at the connector, so wiring good. Still nil response. WIth deck vertical, no platter or cartridge, I turned the large gear slightly clockwise. Platte…
Beogram 3400 Turn button operative, no other controls operative
in BeoGram · Dec 22, 2019 15:50Martin, Thank you and yes, I always put a weight on the center disc, an easy mistake to make if you've not already made it (which I did when I worked on my first B&O table)
Beogram 3400 Turn button operative, no other controls operative
in BeoGram · Dec 21, 2019 19:51A fix for a friend, inherited with a large record collection. I've restored several of the parallel trackers, but never tackled one of these. If I press and hold Turn, the platter spins as it should, stopping when I rele…
Beosound 9000 Mk1 with multiple issues
in General Discussion & Questions · Feb 23, 2019 02:24No. I have been busy working on reel to reel tape recorders. Your expert advice is appreciated and I will reply with details on the CD drive when I remove the sledge and inspect it.
Beosound 9000 Mk1 with multiple issues
in General Discussion & Questions · Feb 13, 2019 16:19Schletti82 I set the arrows on the bottom correctly for testing the unit flat on a table. I really did read the manual before I started work! The noise sounds like a noisy motor or perhaps coming from the CD top clamp. T…
Beosound 9000 Mk1 with multiple issues
in General Discussion & Questions · Feb 10, 2019 22:15Schletti82 Danke Schon Should I fix the noise that the CD makes when spinning before I buy a laser?
Beosound 9000 Mk1 with multiple issues
in General Discussion & Questions · Feb 10, 2019 18:21One thing is very clear in the manual. If the laser cannot focus, the CD motor will not start. That is telling me: - the faint clicking I can hear (1-5 clicks maybe) is the laser trying to focus - as the CD spins most ti…
Beosound 9000 Mk1 with multiple issues
in General Discussion & Questions · Feb 10, 2019 17:47Beobuddy, understood. I have only every changed a CD by opening the door. I was running TM 67 in different positions by pushing the button under that CD. Until I understand why the CD is not spinning properly and is some…
Beosound 9000 Mk1 with multiple issues
in General Discussion & Questions · Feb 9, 2019 18:21Beobuddy, thank you. I cleaned the lens with a just opened alcohol impregnated lens cleaning wipe, wrapped round a Qtip (cotton bud) I then loaded in slot 2 a CD that looks good and does play on my Beosound 2000 - that C…
Beosound 9000 Mk1 with multiple issues
in General Discussion & Questions · Feb 9, 2019 02:14duplicate deleted.