Beocord 8004. Playback only short time..

in BeoCord · Jun 29, 2023 09:12 GMT

Finally, its a winner, thanks to you Martin. I got the HK2500 tapedeck up and running. Just new belts then OK. Then I tried my testtape in it, and the tape was full of dropouts, and very bad overall. Then tested a lot of…

Beocord 8004. Playback only short time..

in BeoCord · Jun 28, 2023 12:05 GMT

yes to all. I will try to find another tape, and also have another tapedeck (working) and will make a new recording on that. Will a bad/very old tape have that performance, sounds OK a short time, then silence. ?

Beocord 8004. Playback only short time..

in BeoCord · Jun 27, 2023 08:50 GMT

Result of checking the 7 volt. Both L and R were 6,89 Volt and the 14 volt is 13,8 Volt. So I think thats fine. But again, with 50 hz hum on the tapehead, I get fine signal in both channels as long as I will. Is it possi…

Beocord 8004. Playback only short time..

in BeoCord · Jun 26, 2023 07:48 GMT

No time yet, but will do it soon. Thanks again for fine info,

Beocord 8004. Playback only short time..

in BeoCord · Jun 23, 2023 11:58 GMT

The Recording is OK. Only one head. Tape is running perfect on head. Only Playback problem..

Beocord 8004. Playback only short time..

in BeoCord · Jun 22, 2023 07:42 GMT

Hi Martin. I will check the 7v ref. But Dolby is OFF. Yes the VU follow the sound. If I gently touch the pins on tapehead, L and R, with my screwdriver I get 50 Hz hum i both. Very clear, steady and strong signal. No dro…

Beocord 8004. Playback only short time..

in BeoCord · Jun 21, 2023 09:28 GMT

The CDX 2 is now fine, so here is another "almost there" project. Beocord 8004. Installed new belts, new LEDs in display, ( VERY small) , and gave it a good cleaning. When play is pressed, it only plays for approx. 1 sec…

CDX 2 Repair , almost there..

in BeoGram · Jun 21, 2023 09:14 GMT

Thank you. I found the 3300 service manual and the schematic. Almost the same as in CDX 2. The problem was the (too high) positive voltage to motor. ( LID up.) It was 8 volt. I could not find any defective components, so…

CDX 2 Repair , almost there..

in BeoGram · Jun 15, 2023 07:16 GMT

Hi Martin, thank you for answer. (er du ikke dansk, syntes jeg har set Dillen navnet før ?) I cant see how LID adjustment is possible, the lid switch is mounted with 2 small screws and it have very little tolerance in ho…

CDX 2 Repair , almost there..

in BeoGram · Jun 12, 2023 08:45 GMT

problem solved. By lubricating the belt with a little grease and reduce the friction it works now. Opens and lid stops at top without crakking.

B&O CDX 2 alomost there,,,repair

in BeoGram · Jun 8, 2023 12:27 GMT

Hi When lid close and hit the mecanical stop (horizontal stop) it makes a little short jump of 2 mm and then closes fully. Everything else is fine. I have replaced the blue cap. on the motorcontrol PCB 8 board to the rig…

CDX 2 Repair , almost there..

in BeoGram · Jun 8, 2023 09:49 GMT

Hi. New gear and belt for the lid, and its nearly OK. Only problem is when lid close, it makes a little "jump" 2-3 mm, then closes fully. I changed the blue cap. on the motor control pcb 8. It was 20 uF so I changed it t…

Beomaster 6000 vækkes til live

in General Discussion & Questions · Aug 12, 2021 12:34 GMT

Hej til jer alle. Efter rep. af flere japanske og engelsk hifi har jeg altid syntes at B&O lavede flere pæne radioer. Har i forvejen en 1900-2 som stadig virker. Nu fandt jeg denne Beomaster billigt sammen med en Beocord…