Posts by matapan
72 total posts52 results
Beolab 8000 Line Input and Powerlink Switching
in General Discussion & Questions · Dec 29, 2025 02:06Does anyone on this forum have a setup in which they connect their Beolab 8000 speakers to their Beosound system via Powerlink, and also connect their conventional home theater system using the line inputs on the speaker…
Lintronic Application Notes for RS485
in General Discussion & Questions · Dec 4, 2025 06:26Hi there, Does anyone on this forum have the application note published by Lintronic for how to control multiple TT455-RT238 units over RS-485? The Lintronic site had a link to the documentation which is stale now. Thank…
Beolab 8000 Setup with non-B&O HT system and Beosound 9000
in General Discussion & Questions · Mar 12, 2025 18:05Hi there, I'm wondering if it's possible to connect a set of four Beolab 8000's in such a way where it will work with a Beosound 9000 for listening to music and also with a conventional home theater receiver with pre-amp…
Beosound and Conventional HT Equipment
in BeoSound · Feb 14, 2023 04:49Hi there, Has anyone on this forum integrated their beloved Beosound audio systems with a conventional home theater setup? Just curious if anyone has done this, and how they have set things up if they have. Thanks!
Integrating a Beosound System w/Conventional AV Receiver
in BeoSound · Jan 24, 2023 07:36Just wondering if anyone has set up their beautiful Beosound systems with a conventional A/V receiver which acts as a hub for a conventional TV set. In browsing the forum today, I noticed that B&O now offers an updated h…
Lintronic HW v4 users?
in General Discussion & Questions · Jan 18, 2016 16:21To be fair, I think it's a reasonable expectation for the vendor to stop support of an obsoleted product once it's been announced, especially a v4 unit. Michael did provide ample notice of this change when it occurred. I…
Lintronic HW v4 users?
in General Discussion & Questions · Jan 7, 2013 21:49Just to be clear, there have been multiple hardware versions of the Lintronic device. The version is described on a sticker located at the bottom of the unit. The most common versions out there are HW v.5.x and 6.x. Thes…
Lintronic HW v4 users?
in General Discussion & Questions · Dec 30, 2012 21:56No Lintronic HW v.4 users out there?
Lintronic HW v4 users?
in General Discussion & Questions · Dec 24, 2012 16:54Hi, Are there any users of Lintronic's TT455-RT238 HW v.4 out there? I recently purchased one second hand and would like to correspond with you.
Beolab 8000 disassembling frustration!!
in General Discussion & Questions · Dec 1, 2012 15:51Do you happen to know what the output voltage is from Standby Transformer T2?
Any Lintronic Users Out There
in General Discussion & Questions · Feb 2, 2012 21:19Do you use a Lintronic code translation device? If so, have you ever used Command 232, the command set related to serial communications? If so, I have some questions for you. Please PM me. Thanks.
BeoSystem 4500 Restoration
in The Workbench · Jan 16, 2011 01:43#8 Polish refers to the finish level of the stainless, which is a mirror finish.
Glass doors for an Overture
in Wanted · Jan 15, 2011 03:00If you have the metal brackets that were attached to the tops and bottoms of each door, have you considered just going to your local glass shop and having them fabricated, then gluing on the brackets? Some of the bracket…
BeoSystem 4500 Restoration
in The Workbench · Jan 15, 2011 02:51Looks really nice! About two years ago, I also restored a Beomaster 4500 to sell. The mirror panel was hacked up and there was no way it could be saved. I did find out that the panel was just a thin veneer of polished al…
Beolink 1000 Repair?
in The Workbench · Jan 14, 2011 20:57No joy. Thanks for the reply though. Does anyone know what kind of discrete component exists on the left side of the board, approximately 3cm below the LED, with the component side facing up. On my board it is light blue…
Beolink 1000 Repair?
in The Workbench · Jan 14, 2011 14:41I've got a Beolink 1000 remote that doesn't work. It is the version that has the clear film holding the copper convex contacts over the PCB. At first, I thought the battery compartment was corroded, so I bypassed the com…
Using the VGA Input on an Avant US
in General Discussion & Questions · Jan 4, 2011 13:31Hi Russ, Thanks for the reply. One last question. Will a cable like this one work? http://www.amazon.com/VGA-RCA-Component-RGB-Cable/dp/B000FM3EQ0 Or, is there more involved in converting the signal? Thanks, John
Using the VGA Input on an Avant US
in General Discussion & Questions · Jan 3, 2011 00:50Thanks for the info! What mode is the set available to use the component video input? V.AUX? Regards, John
Using the VGA Input on an Avant US
in General Discussion & Questions · Jan 2, 2011 17:47Hi, Does anyone know how to use the VGA connector on the back of an Avant US, type 8490? I want to connect my Mac to the set and watch movies via iTunes. Any help would be appreciated! Thanks, John
Beolink PC Office
in General Discussion & Questions · Dec 1, 2010 18:12That would be great! I appreciate the help!