Posts by lostmyshoe
30 total posts22 results
4002 5511 Started running very slow on 45 RPM Speed
in BeoGram · Jan 5, 2014 08:01How did you measure the speed so accurately?
Beogram 4002 Won't play-Everything works
in Imported Content (Unmapped) · Dec 27, 2013 08:43Hi, to check if the shutter/photocell mechanism is working, remove the pickup cartridge, put a record on platter and press play. If you gently push the pickup arm towards the centre of the record, the carriage mechanism …
Beogram 4002 platter
in Imported Content (Unmapped) · Oct 2, 2013 15:45Hi, I'm looking for an unmarked platter for a Beogram 4002 (DC motor version). Thanks Richard
Beogram 4002 black lead screw pulley
in Imported Content (Unmapped) · Sept 15, 2013 19:17Hi, I'm looking for a lead screw pulley for a late model Beogram 4002, thanks Richard
Beogram 4002 (5524)
in BeoGram · Sept 11, 2013 08:10Found the cause of fuses blowing to be a defective mains transformer. On running the turntable from an outboard 24 v ac supply, everything is fine. Thanks for help given, all the best Richard
Beogram 1100 record player tone arm faulty & loose platter
in General Discussion & Questions · Sept 8, 2013 15:57Hi, regarding the tonearm, it needs the weight of the pickup cartridge to stay in the normal position. Secondly the arm will not track the record without a pickup cartridge fitted. Thirdly, the platter just lifts off, so…
Beogram 4002 (5524)
in BeoGram · Sept 7, 2013 18:52Hi, the mains voltage is 240 v, and the two fuses are T250 mA slow blow. If the arm isn't dropped on the record the fuses don't blow. When a fuse does blow there is no smell of overheating etc, and when replaced everythi…
Beogram 4002 (5524)
in BeoGram · Sept 7, 2013 18:41Further to my last post, I've checked the current going to the solenoid coil. It measures 140 mA approx., which is in spec. What other circuits begin to operate after the arm drops which could cause the fuse to blow? All…
Beogram 4002 (5524)
in BeoGram · Sept 4, 2013 12:17Hi, regarding the magnet coil circuit, I've changed TR9, TR10 and IC4 transistors, all the tantalum capacitors, and checked the solenoid coil (measures 8 or 9 Ohms). The problem is just the same. Everything appears to wo…
Beogram 4002 (5524)
in BeoGram · Sept 1, 2013 13:36Hi, thanks for your reply. My deck might be a slightly different version, as it doesn't have the microswitch near the solenoid. If I replace the fuse everything works again until the arm is lowered. The solenoid operates…
Beogram 4002 (5524)
in BeoGram · Aug 31, 2013 15:43Hi, I'm gradually repairing a Beogram 4002 (type 5524, DC motor). Everything now works as far as I can tell until the arm solenoid engages, then one of the two power fuses blows. Does anyone know where I should check for…
Beogram 4002 (5524)
in BeoGram · Aug 22, 2013 13:23Hi, advice needed. I'm trying to rebuild a Beogram 4002. The small pulley wheel on the end of the brass lead screw has a split centre, so cannot be secured properly. Has anyone repaired the fixing or know of a modern rep…
Beogram 4002 type 5524
in BeoGram · Aug 19, 2013 18:23Hello, does Dillen still supply the capacitor kit for this turntable? Thanks
Beogram 1200 Platter
in General Discussion & Questions · Aug 14, 2013 14:00I believe you turn the 45 adaptor in the centre of the platter till it pops out. Pull vertically to remove it, underneath are three securing screws. Regards Richard
Beogram 1202/3000 silent contacts
in BeoGram · Jul 22, 2013 13:03Hi, looking through your method to clean the contacts seems very complicated. I'm probably being stupid, but if the two rivets holding the silent contact fitting were drilled out, would it be possible to slide it out, cl…
Beogram 1202/3000 silent contacts
in BeoGram · Jul 21, 2013 18:10Hi, is there an easy way to clean the silent contacts, without completely stripping the mechanism?
Beovox S30 type 6317
in Imported Content (Unmapped) · Jul 14, 2013 17:52Hello, is it still possible to get a replacement capacitor kit for these speakers? (Beovox S30 type 6317)
Beomaster 1700
in Imported Content (Unmapped) · Oct 24, 2012 21:19Hi, thanks, payment sent by paypal, regards Richard
Beomaster 1700
in Imported Content (Unmapped) · Oct 24, 2012 20:39Hi, I'm interested in buying the clutch washers from you. Could you let me know the cost including postage to England? Regards Richard
Beomaster 1700
in Imported Content (Unmapped) · Oct 23, 2012 17:52Hello, it's definitely the clutch washers, as the tractor belt isn't slipping. If I bought the washers from you would you be able to supply a fitting guide? Regards Richard