Posts by Peter8300
90 total posts73 results
Beogram 2000 (same as 1203 or 3000) Type 5240: arm come back before lifting
in BeoGram · Jan 31, 2026 19:48Try to take off the cam wheel and clean it thoroughly with water and soap and/or isopropylalcohol. All the levers should move freely including the cobber ones. There should be NO grease or oil on it. That has helped me m…
Beogram 3000 Type 5214 signal wiring
in BeoGram · Jan 18, 2026 16:27Mark-sf wrote: I’m not sure I understand your question. The solder connections all look sound. By rewiring are you planning to replace the wire? These are simply terminals so as long as they match the other side’s wiring…
Beogram 3000 Type 5214 signal wiring
in BeoGram · Jan 17, 2026 10:56I have a Beogram 3000 Type 5214 (the one with RIAA socket) that needs rewiring and cleaning up. It seems like there is more than one way to do it (see pics) but it there one that is best?
Beoplay M3 line in sound skipping
in BeoPlay · Jan 14, 2026 09:08Guy wrote: Peter8300 wrote: After disabling my mesh network and just going with one router everything now works fine. Good to hear - I hope it keeps working! I meant to say, it could also be worth checking that your M3 i…
Beoplay M3 line in sound skipping
in BeoPlay · Jan 13, 2026 21:08After disabling my mesh network and just going with one router everything now works fine.
Beoplay M3 line in sound skipping
in BeoPlay · Jan 12, 2026 13:05Hi Guy, Thank you. No haven't tried that, will do so when I'm back home tomorrow and report back. I spoke with B&O support today and they suggested that it could be due to my mesh network.. Thanks Peter
Beoplay M3 line in sound skipping
in BeoPlay · Jan 11, 2026 19:20I'm trying to create a setup where I connect a Beogram to a Beoplay M3 via line in and then do multi room to a Balance. The M3 is only supposed to be the gateway to the balance. However the sound is skipping all the time…
Beovox S45-2 "hiss"
in BeoVox · Jan 2, 2023 05:58Hi guys, I have a set of Beovox S45-2 where one of them has a noisy hiss on and off. Any suggestions as to what can cause this? Thanks Peter
BG 1202 50 to 60 Hz, Mexico
in BeoGram · Jan 8, 2022 12:44If you take off the frame you can actually see and access the silent switch from the side, no need to take everything apart. You can insert a paper strip like you did Søren and with a small bent painters brush you can cl…
Beogram 1200 with phono cables humming.
in BeoGram · Nov 19, 2021 10:05[quote user="Mark"] The DIN cable has a double shield. Each channel has a shield and the entire cable has one. It’s quite possible the phono cables were not grounded properly inside. Generally, tying all three together a…
Beogram 1200 with phono cables humming.
in BeoGram · Nov 16, 2021 21:53Hey, I'm in the process of renovating a Beogram 1200 with came with phono cables instead of DIN cable. When I connect it to a Beomaster 5500 there's a annoying humming when using the deck. I don't think it's the 5500 as …
Beogram 120X Idler wheel
in BeoGram · Oct 27, 2021 09:43Hi Wolfgang, Sounds great, I will get on it immediately :-) Best Peter
Beogram 120X Idler wheel
in BeoGram · Oct 25, 2021 15:39[quote user="Motorman"] That's not too difficult. The best thing to do is to look for the service manual for the Beogram 1202. For example here: https://elektrotanya.com/bang_olufsen_beogram_1202_3000.pdf/download.html T…
Beogram 3000 innard switching between two decks
in Imported Content (Unmapped) · Oct 6, 2021 19:02Hi all, I have two BG 3000 decks type 5228, one with pre-amplifier and one without. The one without is much nicer on the outside so I'm thinking about switching the internal parts between the two. Is there's anything tha…
Logo sticker for Beogram 1200 / 1202 / 1203 dust cover
in BeoGram · Sept 24, 2021 18:43[quote user="Beozip"] Hi Peter, maybe this one can help you out ... https://www.ebay.de/itm/323654130774?var=512656537299 It is NOT the original Logo sticker but it looks good too. [/quote] Thanks, I'll take a look... Pe…
Beogram 1200 dead right channel
in BeoGram · Sept 24, 2021 11:43Thanks Mark, I'm not very experienced in using an Ohm meter and reading diagrams but I got it fixed nevertheless. I cleaned the contacts of the mute switch with grain 400 paper and bent them a little and that fixed the i…
Beogram 1200 dead right channel
in BeoGram · Sept 23, 2021 10:55Ok, so I fixed the dead right channel issue. The pass through connection at the pre amp socket was broken, bent it a little and voila. See picture below, it's the one where the cotton bud stick is pointing. So now there'…
Beogram 1200 dead right channel
in BeoGram · Sept 22, 2021 07:21Thanks Mark, I will give it a try and report back.
Beogram 1200 dead right channel
in BeoGram · Sept 20, 2021 09:56Dear all, I'm working on a BG 1200, got it working all the way except there's no signal in the right channel. I have measured from the DIN plug to the per amp socket, from the pre amp socket to the pick up socket and fro…