Posts by jesperb
86 total posts74 results
RIAA HyperWire MD-001 from SoundsHeavenly
in Imported Content (Unmapped) · Jul 4, 2021 12:34Used for my Beogram RX1, but sold the RX off. You will need a RCA<->DIN converter cable too. Price DKK 200,- (around €30) + p&p. Paypal or MobilePay (in DK). Only shipping to EU due to customs etc. Or pickup/exchange in …
BEOMASTER 6500 does not start up - one error found
in Imported Content (Unmapped) · Jan 16, 2021 17:46Looking at the pictures, Keri seems to have already swapped out 4C1 (the backside of the PCB shows the position as empty), which presumably was the exploded one. So maybe a good idea to swap out 4C10 too ?
Beomaster problem after Recap
in Imported Content (Unmapped) · Jan 16, 2021 14:38Nevermind, since you got it working - I just meant the old red caps on the sound control board. And i think they are in Martins kit, so maybe I have been looking at a before pic in your shared album 😁 Well done, chapeau…
Beomaster problem after Recap
in Imported Content (Unmapped) · Jan 16, 2021 09:20Maybe the 2 red Roederer caps in the volume section of the control board has something to do with this ? They should go as well. Don't buy big ones, then you won't be able to close the lid 😁
Beovision 10-46, how to select HDMI as input ?
in General Discussion & Questions · Dec 27, 2020 13:44Thanks beojeff & Millemissen, Reading the manual was - of course - at LOT smarter, than messing about in the Beoworld forums ;-) https://bangolufsenassistentgohe.blob.core.windows.net/manuals/TELEVISIONS/BEOVISION_10/beo…
Beovision 10-46, how to select HDMI as input ?
in General Discussion & Questions · Dec 27, 2020 12:06Hi, A friend has a Beovision 10 and we're trying to get it work with a new Chromecast, but no luck. Rather, we cannot find out where to select HDMI as input. Any help in this appreciated -we expect the Beovision should '…
B&O Beogram 5005 (problem: low sound output)
in Imported Content (Unmapped) · Oct 26, 2020 08:22Hi Pablo, Congratulations on your Beogram 5005. It's a great looking unit. I think you may need an RIAA amplifier between your Beogram 5005 and your amplifier. Beogram 5005 does not have a RIAA built in. This includes my…
Beomaster 4000 Restoration - Someone left the cake out in the rain.
in Imported Content (Unmapped) · Aug 19, 2020 17:24Sorry but no I don't. But since it's an easy DIY project, anybody can do it at home. Just forgotten all about it until i read your post. Only thing that triggered my memory was that it's an old trafo, difficult to find a…
Beomaster 4000 Restoration - Someone left the cake out in the rain.
in Imported Content (Unmapped) · Aug 19, 2020 16:05Back in the days, when i was a trainee, at a small electronics plant making inverters (way before the solar boom), we also wound - or coiled - our own transformers (don't know the correct term). When done, we would put t…
Beomaster 5000 all inputs play 'TP1' ?
in Imported Content (Unmapped) · May 30, 2020 07:46Forgot all about this post, but of course I had used the outputs. Tx Martin :-)
Beomaster 5000 all inputs play 'TP1' ?
in Imported Content (Unmapped) · May 8, 2020 10:15Thank you Martin, I'm using the jack-plugs (phono-plugs?), so that cannot be the case. Forgot to write that little detail. So it could be because i have connected the jack-plugs on outputs rather than inputs ?
Beomaster 5000 all inputs play 'TP1' ?
in Imported Content (Unmapped) · May 8, 2020 09:10Hello, Not sure if the subj is representative, but I recently got a Beomaster 5000 that 'just' needed no-load current adjusted in one channel. So it plays fine. Yesterday i discovered, that when there is signal on TP1 (C…
Beomaster 5000 'thingy' - where does it belong (ground spring) ?
in General Discussion & Questions · Apr 19, 2020 21:28Makes sense, since i had the board upright, to make room for the idle current adjustment. Board held itself upright just fine without the 'spring' though. Thank you.
Beomaster 5000 'thingy' - where does it belong (ground spring) ?
in General Discussion & Questions · Apr 19, 2020 20:53Hi, got a Beomaster 5500 and was adjusting idle current. When i was turning the unit over, this 'thingy' fell out. I cannot find it on the drawing in the service manual. Maybe someone knows where it belongs, so i can ret…
Beomaster 1900 amplifier issues
in Imported Content (Unmapped) · Jul 3, 2019 05:50Like you write yourself 'You live and you learn...'. I also took quite a long break, before swapping the output transistor - and for the exact same reasons ;-) Re. the tone level, I recapped the tone/balance board comple…
Beomaster 1900 amplifier issues
in Imported Content (Unmapped) · Jul 2, 2019 21:33Bit late with the answer, but i had the same issue on my 2400. Standby when powered on. Pulled left outout tranny. Startup now OK and played fine in the right channel only. Had recapped and swapped all trannies in the ou…
First attempt at Beomaster 2400 'refurbishing'
in Imported Content (Unmapped) · Apr 9, 2019 09:20I thinks this project is almost done. Did a FM tuner check yesterday, reception is surprisingly good, with only a short length of 0.75mm2 wire pushed into the antenna plug 😁 Only headphone hum left to fix. Tried two dif…
First attempt at Beomaster 2400 'refurbishing'
in Imported Content (Unmapped) · Apr 6, 2019 07:30Got a little spare time, which immediately went into the Beomaster 2400 on the kitchen dining-room workbench (no room for guests this week). Looking at the 'volume up mute' issue, where volume would play briefly and then…
First attempt at Beomaster 2400 'refurbishing'
in Imported Content (Unmapped) · Mar 17, 2019 19:51...i go my lamps from Dillen (too).
First attempt at Beomaster 2400 'refurbishing'
in Imported Content (Unmapped) · Mar 17, 2019 17:30Honestly ? I don't know. I bought them as a 'Beomaster repair kit' and no markings. Try do a search, lots of discussions about the lamps.