Posts by thomasf
15 total posts14 results
The Beoworld December 2025 Prize Draw
in Prize Draw · Dec 19, 2025 18:01Glas filled with bubbles, the fire is on! 🥂
The Beoworld December 2025 Prize Draw
in Prize Draw · Dec 19, 2025 05:55Soon time to put the kettle on ... 🥳
The Prize Draw - Thoughts Please...
in Prize Draw · Feb 17, 2023 10:51Hi all, Similiar to Miki, I joind the community to get ideas, chat and access to manuals etc, not for the prize draw, which I found out later and saw as an exiting bonus! As long as I have an interest in old B&O equipmen…
THE BEOWORLD CHRISTMAS 2022 PRIZE DRAW !!
in Prize Draw · Dec 22, 2022 21:04The wine is in the glass, prepared for the draw! Bring it on! ?
The BeoWorld Spring 2022 Prize Draw !!!
in Prize Draw · Mar 31, 2022 19:56The wineglass is not empty! ? Keeping the fingers crossed! ??
Beomaster 6000 and datalink protocol
in Imported Content (Unmapped) · Feb 7, 2022 14:49Hi all, Short update on my progress with the Beomaster 6000 restoration. I have worked a bit with the frequency counter, so now the device shows the (almost) correct frequency for the selected radio program. I have no FM…
Beomaster 6000 and datalink protocol
in Imported Content (Unmapped) · Jan 17, 2022 07:31[quote user="pilatomic"] Anyway, I gathered some knowledge about the "old" datalink protocol, you can find all my notes in my project git repo : https://gitlab.com/Pilatomic/beobridge/-/tree/master/datalink Keep up with …
Beomaster 6000 and datalink protocol
in Imported Content (Unmapped) · Jan 16, 2022 19:48Thousands thanks manfy! Wow - yes that was a wonderful site! I had not seen it before - and as a Swede I have no problem to read Danish! 😕 I will surely read the chapter about the remote control and the datalink before …
Beomaster 6000 and datalink protocol
in Imported Content (Unmapped) · Jan 15, 2022 17:53[quote user="manfy"] Hmmm...2 seconds? Why? And what happens to the outputs after those 2 seconds??? Looking at the circuit diagram and page 6-7 of the service manual I would think that those volume preset buttons should…
Beomaster 6000 and datalink protocol
in Imported Content (Unmapped) · Jan 15, 2022 09:01Ciao manfy! Thanks for your tips - it is slowly coming back to life! 😕 Yesterday I got the volume going - the motor drivs the pot as expected - but I have one question regarding this. When I press volume down I assume t…
Beomaster 6000 and datalink protocol
in Imported Content (Unmapped) · Jan 13, 2022 12:59[quote user="manfy"] Yes, indeed. Nobody forces you to re-code the BeoFirmware the very same way as the original. ... If this were my own project, I might not want to give up on datalink so easily, though. Fair enough, y…
Beomaster 6000 and datalink protocol
in Imported Content (Unmapped) · Jan 13, 2022 07:23Hi Manfy! Thanks for your comment! I'm using a PIC16F887 which have all I need, timers, GPIO's etc. It was not completely pin-compatible, so I had to swap some pins which can be seen on the "prototype build" in the pictu…
Beomaster 6000 and datalink protocol
in Imported Content (Unmapped) · Jan 10, 2022 19:54Hi, Edit: Subject renamed from Beolink to more correctly "datalink" I recently bought an Beomaster 6000 (225x) in an unknown state. After some digging and measurement in the device I came to the conclution that the CPU w…
BEOMASTER 6000 TYPE 2251 HELP NEEDED
in Imported Content (Unmapped) · Jan 2, 2022 16:29Hi Christian, [quote user="Spassmaker"] So i give that beast another try and check the Keyboard, hope to find something. [/quote] Did you have any luck with your BM6000? I'm in almost the same situation that you where ba…