Posts by spassmaker
394 total posts350 results
Beocenter 9500 Co.de
in General Discussion & Questions · Jun 18, 2026 18:36Hi there Really no one? Does anybody know about different Codes maybe for older models? Have already found the usual 1271 and 1207 both did not work 😢 Maybe renew the 8 PIN static RAM? Any help would be appreceated. Tha…
Beocenter 9500 Co.de
in General Discussion & Questions · Jun 14, 2026 16:33Bad news.... For some saftey reasons I put in a new battery, now both uPc boards have the same behaviour, even I swap the EEPROM's. Co.de is displayed and nothig there to get rid of this. Oh dear what have I done wrong?
Beocenter 9500 Co.de
in General Discussion & Questions · Jun 14, 2026 15:49Hi J6st came back from a short journey where I bought a used BC 9500 for a couple of €'s Took me 2 hours, the dead Beocenter was unplugged from the mains so long. Tried once more the " code routine" but nothing happens. …
Beocenter 9500 Co.de
in General Discussion & Questions · Jun 14, 2026 11:37Hello dear Members I know it's about the Million Times asked for the Co.de for a Beocenter 9500 With a new Lithium Battery tested. I've read already to: Plug in the Center Type 1271 with Beolink 1000 or Beolink 4 Unplug …
Beolab 2 Highpass Filter in output?
in General Discussion & Questions · Jan 5, 2026 17:11Really no one?😔
Beolab 2 Highpass Filter in output?
in General Discussion & Questions · Dec 30, 2025 13:25Hi dear Members I've got a question about the Beolab 2 Subwoofer if there is a High Pass Filter in the Powerlink Outputs and what is the cutoff frequency. In the service manual is a HPF shown but nothing about the cutoff…
Beomaster 8000 strange parts on Board No 7
in General Discussion & Questions · Dec 1, 2025 08:01Hi dear members I've a question about an BM 8000 eich I'm working on. During inspection of Board No. 7 (Relay Board on the back of unit) I found an capacitor C2 4000uf and two diodes D3 /D4 MR501 on that board which are …
Beogram 8000 No Control From Buttons
in BeoGram · Apr 3, 2025 11:32Hi Jacope Did you renew the cap on the prcessor-board (47uF if I remember) in the uPC - can?, quiet important. Usually there are two flat wires to the front panel. One is just for the display , the other for the buttons.…
Beoremote Halo
in General Discussion & Questions · Nov 5, 2024 14:09Hi Found the screws under the rubber ring, all ok. Thanks again Christian
Beoremote Halo
in General Discussion & Questions · Oct 29, 2024 12:54Hi Thanks for that, I´ ll try next days. Kind regards Christian
Beoremote Halo
in General Discussion & Questions · Oct 28, 2024 14:21Hi dear Members Is there anyone who can give me advice to get access to the battery of the Halo remote? Could not find a service manual, or hints to open the remote from downside, where the battery lives. Mine has gone b…
Beogram 4002 Speed Fluctuations
in BeoGram · Oct 21, 2024 13:08At first I would replace the platterbelt with a new one, if there is still wow you have to dig deeper. Listen without amp but record on if there is some scraping noise from platter to other parts inside. Beoparts (now: D…
Beogram 4000 tonearm not lifting end of record
in BeoGram · Oct 10, 2024 11:43If you adjusted the pot wich is discribed as MOT you would have chaged the amplitude of the platter motor. Nothing related to the differential circurit as far as I know ;-) Maybe you puzzeld a little bit at the other pot…
Question About Beogram 8002 Recapping
in BeoGram · Oct 10, 2024 11:38Hi I'll try to help a little bit. P7 - 12 and P 7 - 6 go to ground because P 7 - 6 is Ground P 7 - 12 has a conection to ground via the motor coils ( 0 L 1) related Plug ( P 4 -2; P4 - 5) . Have not measured the coils so…
Beogram 8000 back to life in a weird way
in BeoGram · Sept 20, 2024 13:23Hi Ary Ordering a capacitor kit from Beoparts (now: Danish Sound Parts)is not stupid, i my opinion it's the best way to get all caps in a set for a dedicated restauration project. Beoparts (now: Danish Sound Parts) is pr…
Beogram 8002 not turning on
in BeoGram · Sept 20, 2024 12:47Hi Jordi The Capacitor that you mentioned is the last I would change because this is the Phase Cap for the Platter Motor mechanism which normally lasts very long. If you got no LED I would resolder ALL solder joints of t…
Beogram 4004 slowing down
in General Discussion & Questions · Sept 10, 2024 10:05Hi Gunnar My question is if the slowing down is sometimes for a second or slowing down for longer time. first case from my experience there is a problem with the spark snubber diodes (TVS diodes) in the motor. Find out d…
Datalink on Beogram Turntable
in General Discussion & Questions · Aug 30, 2024 13:08My question is if the Beogram 4004 would interact with an Beomaster 6000 ( not 4CH) or Beomaster 8000? Thanks for advice. Kind regards Christian
Woofer driver vibration problem ?
in General Discussion & Questions · Aug 8, 2024 11:25Hi Did you replace the foam and gaskets? Could be airventilation caused by gaps between the amp module speaker module or top module with pipe. May be that a PCB is ratteling because of a missing screw or a broken screwpo…
Beogram motor bearings issue
in General Discussion & Questions · Jun 20, 2024 13:11Maybe you get some more information in this discussion: /forum/imported-unmapped/beogram-1200-motor-no-spin-very-hot Lot to read and some pictures. Kind regards Christian