Posts by Pindsen
147 total posts117 results
Speaker for BM800
in BeoMaster · Dec 17, 2025 18:56Here are pictures of the hole in enclousure.
Speaker for BM800
in BeoMaster · Dec 17, 2025 18:54Here are pictures of the speak. It is 13cm wide, 7,5cm height and diagional between upper left and lower right screw are 12,7cm.
Beomaster 800 burning out R225? Insight welcome.
in BeoMaster · Dec 15, 2025 19:03Hi, Have you fixed the issue or do you still help? /Pindsen
Speaker for BM800
in BeoMaster · Dec 15, 2025 18:54Hi, The speaker seems special in the Beomaster 800, it has a 50R resistor built-in and is hard to find a replacement for. I have a BM800 where one of the speakers are dead (infinite ohm across coil), so either I find a B…
Search issue in forum 2012-2022
in BeoWorld Feature / Problem · Aug 5, 2025 19:43Okay, the Google string works, it provides the search results in separate links - but it's useable. I just tried if the search function works Today, but still get the same message: Sorry, we were unable to find any resul…
Search issue in forum 2012-2022
in BeoWorld Feature / Problem · Aug 1, 2025 15:57Hi, If I try to search for a topic, could be "Beogram CD 50" in the older forum 2012-2022 I get nothing. I tells me this "Sorry, we were unable to find any results using your search terms. Please change your search terms…
Beomaster 2400 Restoration Problem
in BeoMaster · May 3, 2025 18:55Hi, I assume you have changed 2C92 (2200uF). I had something similar once (but also ripple noise in speakers) where ripple on 2C92 capacitor was too high due to defective rectifier (2D50). I changed to a 6A rectifier and…
BM1900 Level adjustment
in BeoMaster · Apr 30, 2025 19:13Hi, In the service manual for Beomaster 1900 one shall apply 200mV 1kHz signal, is it 200mV peak or peak-peak? It also says to measure 100mV on the output, I assume it is on an unloaded output and that it is 100mV RMS? /…
What is next for B&O recreated classics
in Discussion · Feb 9, 2025 10:12Beomaster 1900 is a true classic. Keep the 1900 design but replace the plastic "wood" sides with true wood (could be either light or smoked oak). Rename TAPE to AUX. Maybe add datalink to the Phono socket so it can contr…
Left channel issue on Beomaster 4000?
in BeoMaster · Feb 9, 2025 09:04Hi, Good that you figured it out. You mention a 1,5kohm resistor you suggest shall be 2,7kohm - is it 566 at basis of TR53 and why do you suggest this changed value? /Pindsen
beomaster 1900 no 15v supply
in BeoMaster · Feb 6, 2025 19:52Hi, You need to ensure the Switch On signal is present on TR32 Basis after you have activated the touch buttons, otherwise you will not have voltage over the relay coil.
BS Century pinch roller
in BeoSound · Jul 3, 2024 19:12Hi, Where is it possible to buy pinch roller for a BS Century? They are a little special as they have an in-molded 2mm shaft. /Pindsen
Beocentral.com
in General Discussion & Questions · Dec 21, 2023 20:49Hi, There are pages where the production end date is incorrect or not listed eventhough the product is phased out long time ago (Beolab 3, Beolab 17, Beoplay S8 ect.). Other pages are only with a picture but no descripti…
Beocentral.com
in General Discussion & Questions · Dec 20, 2023 09:37Hi, Anybody knows if the Beocentral.com page is still being updated? Seems like last update is many years back. I have tried to contact them but have not received any answer - could be that we could help them keeping it …
serial number and date of manufacture
in General Discussion & Questions · Aug 17, 2023 19:44I saw elsewhere on the Internet that one could also extract the month from the serial - anybody knows how to decode that?
Beogram CD3300 only open 1cm
in BeoGram · Aug 15, 2023 21:01If something is broken of the eject actuator I cannot see what that should be. I though discovered that the hinge in the eject side was touching the actuator arm slightly underneath where they meet, I removed a little pl…
Beogram CD3300 only open 1cm
in BeoGram · Aug 14, 2023 18:57No, gears are fine. The issue is in the other side where the Eject button is. There are some kind of small obstacle that is just enough for the motor not being able to lift the lid. If the lid to assisted slightly it mov…
Beogram CD3300 only open 1cm
in BeoGram · Aug 13, 2023 09:25Hi, I'm struggling with a Beogram CD3300. Belt is changed and so are the 68uF capacitor on motor lid PCB but the lid only opens approx. 1 cm. If a little help is assisted it open up fully but if not it is stuck only 1 cm…
BG with RIAA connect to a PL based Beolab
in BeoGram · Aug 11, 2023 19:14Thank you, I like the Playmaker option. Then it requires a RJ45<->7-pin DIN (male) cable and a 7-pin DIN splitter (female to 2xmale) - correct? /Pindsen
BG with RIAA connect to a PL based Beolab
in BeoGram · Aug 10, 2023 08:06Hi, This question has probably been asked before but searching in the archive I have not found anything. Is it possible to connect a Beogram with built-in RIAA (e.g. Beogram 3500) directly to a Power Link based Belolab (…