Boy, does that look familar!!

You probably can't see me jumping for joy here but believe me, there is jumping happening.

I have to agree with Burantek that "I love this site!". And I just joined when I wanted to get my BM back on the path to health. I must have missed a lot of love over the years that this site has been around.

I'll let you know once I have a look, but already I see a problem in that I originally wired both red wires from the 1 watt resistors to the positive terminal of the middle cap. I see that one is neg and one is pos.

I think I am on the right track now. Thank-you again!

Glad it's hopefully going to do the trick Dan. I too have left the BM opened up in case you need anything further - in fact this is the first time this BM's insides have seen daylight since new! Reminds me I must get a cap kit and lamp off Dillen on this site.  Don't give up...there's always help here.

I wonder if any of you lads can help me with a Beomaster 2000.

sound coming out of right channel is fizzly & distorted (FYI: the speakers are fine & sound out left channel is fine)

Can you tell me what internal parts i should test first in my BM2000?

pics would be helpful as i have no service manual yet.

thanks so much!

Greg,

I saw your other post RE: BM2000

I will post over there and hopefully it will take off.

Have had some sucess in that I get sound out now although at a limited volume with scratchey, thin, weak sound. I am wondering if I still have something shorted that is chocking the pre-amp section or something.

But now I found another issue to tackle and I am looking for direction. I bought a beogram 4004 TT for my BM 300-2 and I went to connect it last night to find the TT has a 7 Pin Din connector instead of the 5 Pin DIN on my BM.

Do you know anyone on here who sels and adapter, or parts to make one, or a pointer to a website where I can buy or make one?

Thanks again...throwing my request out to the magic of Beoworld again...

Hi Dan,

the plug thing will be easy to sort out - the two "extra" pins will just screw off. Look closely and you'll see a tiny slot for a screwdriver at the end of the pin. Don't lose the pins, tape them to the turntable cord or something.

Regarding the other problem, can you feel the Beomaster getting unusually hot anywhere? Is that weak sound with all sources?

Thank-you for insight on pins I will do that.

The BM was not warm to the touch in any area after 15 minutes of use (connected to magnapan loudspeakers) with the weak sound being the same with testing using my laptop headdphone out to a 3.5 mm to 5 pin din adapter I bought off eBay.

I connected to Phono 1, Phono 2, and Tape input. All threee play the music, all three played at same weak, distorted sound.

I should note, that I have one wire not connected to anything up near the Bass slider. 30 years ago my stereo indicator lamp went out and it is pulled up out of its cubby hole with the thought that I could find a replacement lamp someday to fix it and it looks like the loose wire may have connected to the lamp, although it already has two wires connected (one is white with black stripe, and other is black) so this is a solid grey wire that is long enough to terminate to the lamp or somewhere in that area.

I can take a pic and post if needed.

Than-you for quick response. I have business prospects visiting on Saturday and my desire is to have my BM, TT and speakers going in my offic when I welcome them. I will take a picture of my "retro" setup when I finish this. It includes eames furniture, a 2  new 2 inch wool shag rug, and B&O cabinet (all pieces re-finished rosewood).

OK, if it doesn't get hot I suppose you have the power supply connected properly and the idle current setting of the power amps should be about right.

This series of receivers have a habit of getting corrosion on the switches when they sit unused. You could try just flipping trough all of them a couple of dozen times and see if the sound gets better, even momentarily (keep the volume well down to avoid damaging the speakers!). Likewise, if the volume, balance etc controls are "scratchy" they might need a little workout.

I don't have a 3000 myself so the other guys might be able to help you with the remaining mystery wire. The stereo lamp only needs two, so I guess that's not where it came from.

Thank-you all for contributing your time to provide help for my 3000. I have an old used one on the way that I bought on eBay from someone in Canada. I paid $140 for it and hopefully between the two of them (his is a 300-2 Type 2402 also) I can get one good Beomaster up and running.

But all of this revived interest in my 3000 has gotten me wanting to get my true love, a 4400. So now I am approaching users, and hunting eBay for a good condition 4400.

Also, I have a couple bids on Beocord reel to reels as I really love the reel to reel sound (I used to have a Teac r to r back in the 80's). If anyone knows of a nice beocord reel please let me know.

It's funny, back in 2003, I was consulting and had lots of liquid cash and I went to a mid-fi store and bought a whole setup costing just under $10,000. I wish I had the revival impulse back then becasue I could have gotten a very nice vintage B&O setup for about half that amount. Although it would not be 5.1 or 7.1 but I don't care. Most of the stuff I listen to is pure 2 channel music. So I have a nice Rotel Amp and preAmp, and a Project RM6B TT with Sumiko Blue Oyster Special Cart, 5 Quad 22L speakers and I sit and wish I had a Beomaster 4400 or 4401 with Beocord RR, instead. Although I did get a Beogram 4004 two weeks ago, and although I have only heard it twice, becasue of the 3000-2 in a weakened depressed state, I am excited to use that one the dust settles on getting a working beomaster back online. I also have a pair of magnapan IIa I bought off eBay last month specifically for the B&O setup (and of course I had to get the B&O open rosewood cabinet from eBay to hold the rosewood B&O equipment. I'll post some pics if others would like to see. It all comes together nicely on the shag rug and all.

Dan,

I replied here for your requests.

Dan Gleason wrote:

I was consulting

Ah... the grand old consulting days... how I miss them!

Sometimes... I think I am living my life backwards... Benjamin Button... I am. 😂