Dear All,

I found on B&O web site the latest firmware version (15-01-18) for the BeoLab Transmeter 1.

I applied to my device.

Previous version was 192.5, now it's 204.1.

Firmware upgrade was done without any problem.

My system is:

Television BV7-55 -> BL Transmiter 1 (3 cables : front, surround and back)

- Front : 2 x BL18, FW: 189.8

- Surround : 2 x BL17, FW: 189.8

- Back : 2 x BL6000 via 2 x  BeoLab Receiver 1, FW: 204.1

None of the speakers, either BL17 or 18, have been updated. Remark: the BLR1 is already at the latest version.

I don't see any clue in the debug file why upgrade was not done (look at the end of this post).

Of course, I followed the guide provided with the upgrade. And I tried three times. Before the last one I powered off all devices for, at least, 60 real seconds.

Thanks for your help.

Tux

******************************************************************************************************************

FW version (file versions.txt):

Versions in zip-file:
wpl_tx:   1.1.4.5310 (FEP: 1.15a), (DSP: 0.60a), (SUMMIT: 0204-01)
BeoLab17: 1.1.5.6210 (FEP: 1.90a), (DSP: 1.96j), (SUMMIT: 0204-01)
BeoLab18: 1.1.5.6210 (FEP: 1.90a), (DSP: 1.96j), (SUMMIT: 0204-01)
BeoLab19: 1.1.5.6210 (FEP: 1.90a), (DSP: 1.96j), (SUMMIT: 0204-01)
BeoLab20: 1.1.5.6210 (FEP: 1.90a), (DSP: 1.96j), (SUMMIT: 0204-01)
BeoLabR1: 1.0.1.6211 (FEP: 1.00a),               (SUMMIT: 0204-01)

******************************************************************************************************************

Content of the debug file:

[00003084]Summit uart: Olympus FW Ver 204.1 (May 11 2017) Debug
[00006755]Summit uart:
ourceID = 9588
[00006766]Summit uart: DeviceID = 0x16,  BranchID = 0x02
[00006813]MEMSTICK SW update check starting 00004534 Total 00004534

[00006835]Summit uart: System Data CHECKSUM Error...Calling I2CSlaveWriteRelease()
[00006846]Error message from MCC 16 Seen since boot 1

[00006864]NumberOfSpeaker : 6
[00006880]WPL         : Event  0 received in state 0, new State 2

[00007176]DSP booting from FEP!
[00007387]WPL         : Event  2 received in state 2, new State 2

[00007513]WPL         : Event  5 received in state 2, new State 2

[00007529]Summit uart: CHECKSUM Error...Calling I2CSlaveWriteRelease()
[00013034]Summit beacon_cmd (time:5500) Status: 0x01

[00013060]Summit uart: Quality Hop Enabled
[00013420]Summit uart: SpeakerCount for Zone 0: 6
[00013456]Summit uart: Restoring Slave 0... succeeded
[00013491]Summit uart: Restoring Slave 1... succeeded
[00013527]Summit uart: Restoring Slave 2... succeeded
[00013560]Summit uart: Restoring Slave 3... succeeded
[00013599]Summit uart: Restoring Slave 4... succeeded
[00013635]Summit uart: Restoring Slave 5... succeeded
[00013651]Summit uart:  peakerCount for Zone 1: 0
[00013667]restore speaker configuration Status: 0x01

[00013678]Summit uart: SpeakerC5: 0
[00013689]Summit uart: SpeakerC5: 0
[00013726]master Mac Address            02 EA

[00013846]Speaker ID 0 Configuration: Mac Address                   02 EA

[00013857]FW Version                    189-8

[00013877]Speaker Mode=2 Slot=1  SpeakerDescription=0 BeoLab18

[00013999]Speaker ID 1 Configuration: Mac Address                   02 EA

[00014010]FW Version                    204-1

[00014027]Speaker Mode=2 Slot=2  SpeakerDescription=0 BeoLabR1

[00014149]Speaker ID 2 Configuration: Mac Address                   02 EA

[00014161]FW Version                    204-1

[00014177]Speaker Mode=2 Slot=3  SpeakerDescription=0 BeoLabR1

[00014285]Speaker ID 3 Configuration: Mac Address                   02 EA

[00014300]FW Version                    189-8

[00014316]Speaker Mode=2 Slot=4  SpeakerDescription=0 BeoLab17

[00014438]Speaker ID 4 Configuration: Mac Address                   02 EA

[00014450]FW Version                    189-8

[00014466]Speaker Mode=2 Slot=5  SpeakerDescription=0 BeoLab18

[00014595]Speaker ID 5 Configuration: Mac Address                   02 EA

[00014606]FW Version                    189-8

[00014623]Speaker Mode=2 Slot=6  SpeakerDescription=0 BeoLab17

[00014643]WPL_TX SW updating Speaker 0 Not done

[00014654]WPL_TX SW updating Speaker 1 Not done

[00014670]WPL_TX SW updating Speaker 2 Not done

[00014686]WPL_TX SW updating Speaker 3 Not done

[00014697]WPL_TX SW updating Speaker 4 Not done

[00014714]WPL_TX SW updating Speaker 5 Not done

[00014730]MEMSTICK SW update check completed 00007919 Total 00012453

[00014746]MCONF         : Event 21 received in state 0, new State 0

[00015008]MISSING_speaker info cleared

[00015027]WPL         : Event 10 received in state 2, new State 2

[00017579]Summit uart: SpeakerCount for Zone Quality Hop Disabled
[00017625]system_shutdown_cmd Status: 0x01

[00018161]MISSING_speaker info cleared

[00018182]Sense status, PL=0 TOSLINK=0 LINE=0 USBB=0 USBA=0 ATI=0 ALWAYSON=0 TESTMODE=OFF PL/Line Switch=POWERLINK, ASSOCIATED