Just want to listen to music on my Beolab 8000 sometimes...

42 replies

Hi all,

right now I have a Beoplay V1-40 in my living room, with an Apple TV and 2 BeoLab 8000 speakers connected to it. This is an amazing setup for watching movies!

However, when I want to listen to music (typically through AirPlay from my iPhone to the AppleTV), the time between "I feel the need to listen to music" and the moment when the music starts playing drives me crazy. I have to:

- Press "VMEM" on my beloved Beo4 remote

- Wait for a looong time until my TV is turned on

- Switch to "Speaker Mode 2" (default for the source AppleTV is 3, because for movies, that's what I need)

- And THEN I can finally start streaming music

I am looking for a solution where this is instant, I want to push one button to turn on the "stereo", and get going - while still using my gorgeous Beolab 8000 speaker, of course!

Any proposals what I can do?

Thanks in advance,

Christof

Perhaps you could use a Beo1 remote and set a memory button to your desired settings?

You could go down the Moment route, it achieves the one button start.

But means using Deezer and some local music, which works for me, but in the software isn't quite as slick as it should be

1. Daisy-chain your BeoLab speakers or connect them via Y-splitter to be driven from one Din8 connector in the end/

2. Get https://almando.com/index.php/b-o/b-o-apple/almando-multiplay-stereo.html

3. Get https://www.apple.com/airport-express/

4. Connect your TV output to Almando Input 1

5. Connect AirPort Express to Almando SPDIF Input

6. Connect your BeoLab 8000 speakers to the output

Now if you want to listen to the music on any of your Apple gear, just stream it to Airport Express and BeoLab 8000 will turn on "immediately"

If for some reason you are watching TV and streaming music to AirPort express at the same time, priority will always be on Input 1(TV), you will have to switch off TV to get the music from the AirPort Express.

 

didole wrote:
- Wait for a looong time until my TV is turned on
program the Quick-Start Timers (Power Settings - Standby) 
didole wrote:
- Switch to "Speaker Mode 2"
You can first start the music and then switch the speakers with the Beo4 (SPEAKERS - 2)
didole wrote:
I am looking for a solution where this is instant, I want to push one button to turn on the "stereo", and get going - while still using my gorgeous Beolab 8000 speaker, of course!
as proposed a Beoremote 1

Or:

assign a stereo mode (what you call Speaker 2) to the ATV and change to Speaker 3, when you use it for video content.

Or:

connect another AirPlay-capable device and set that up for music listening - assign it to one of the spare buttons/commands on your remote.

MM

Location: Flensborg————Danmark

mczac wrote:

1. Daisy-chain your BeoLab speakers or connect them via Y-splitter to be driven from one Din8 connector in the end/

2. Get https://almando.com/index.php/b-o/b-o-apple/almando-multiplay-stereo.html

3. Get https://www.apple.com/airport-express/

4. Connect your TV output to Almando Input 1

5. Connect AirPort Express to Almando SPDIF Input

6. Connect your BeoLab 8000 speakers to the output

Now if you want to listen to the music on any of your Apple gear, just stream it to Airport Express and BeoLab 8000 will turn on "immediately"

If for some reason you are watching TV and streaming music to AirPort express at the same time, priority will always be on Input 1(TV), you will have to switch off TV to get the music from the AirPort Express.

 

Isn't it strange that the only complete solution requires buying a third-party product? Shouldn't buying a device like the Essence/Core also provide the capability to stream music to my Beolabs without either waiting for ages for the TV to turn on, or running the TV in a power-consuming "Quick Startup" mode?

I would have to give up my beloved Beo4... Used to it since 1996 (when I got my Ouverture).

To get around the speaker setup problem, how about using a cheap hdmi splitter on the ATV output, and connecting both to two different hdmi inputs on the BV1.  Hence when selecting the 'music hdmi' the default can be Speaker 2. 

Location: Warwickshire, UK

My B&O Icons:

BeoCenter-9500.png BeoCenter-9500.png
Beoremote-Beo4.png Beoremote-Beo4.png
Beovision-10.png Beovision-10.png
Beotime.png Beotime.png
Beosound.png Beosound.png
Beosound-Explore.png Beosound-Explore.png
Beosound-Essence.png Beosound-Essence.png
Beoplay-P2.png Beoplay-P2.png
Beoplay-M3.png Beoplay-M3.png
Beoplay-H4.png Beoplay-H4.png
Beoplay-H3.png Beoplay-H3.png
Beoplay-Form-2i.png Beoplay-Form-2i.png
Beoplay-Earset.png Beoplay-Earset.png
Beoplay-A2.png Beoplay-A2.png
didole wrote:

I would have to give up my beloved Beo4... Used to it since 1996 (when I got my Ouverture).

I had the same problem, I bought beo5 and beo6 sold them

It took years but after finding Beoremote 1 I moved on and replaced all Beo4

or
BeoWorld Gold Membership card
Join BeoWorld

Register to access the forums, reference material, and exclusive member benefits — including our monthly prize draw.

Become a Member

December 2026 Prize Draw

Gold Members Only

As a Gold member you're automatically entered into our exclusive prize draw — your chance to win iconic Bang & Olufsen products. A unique benefit of BeoWorld Gold membership, every draw brings a new opportunity to win something special.