BV7-40 MK3, red standby LED blinks

13 replies
T(
Offline
timhanna (archived)
Bronze
Posted December 4, 2008 at 04:03 GMT
#1860680

It first started recently, 30secs after switching off the TV the red LED starts blinking. I do have a PIN code attach to the TV, but the power was never disconnected.

Does anyone know what this might be?

Thanks,

Tim

stefan
Offline
stefan
BronzeFounder
Posted December 4, 2008 at 04:56 GMT
#1860681

Maybe a Masterlink problem. Disconnect the mains for about one minute and reconnect. Everything should be fine now.

Stefan 

T(
Offline
timhanna (archived)
Bronze
Posted December 4, 2008 at 05:02 GMT
#1860682

Hi and Thanks for the reply Stefan.

I did, and it did go away, ok, it wasnt 1 minute... but the thing is that a couple days later it happened again...

Ill try it for a minute today... strange...

Q(
Offline
Quim43 (archived)
Bronze
Posted December 4, 2008 at 05:11 GMT
#1860683

Hi Tim

I think it can be a software issue. Look what the new software fixes:

Build 433 (H8 SW 5.02). Support for DVB-HD. Teletext in P-P gives TV+TV. Intermittent loss of the PUC Table.

New features:

  1. Support for DVB-HD (only released in some markets).
  2. A of this SW release, the TV menus are black instead of grey and are placed on the left side of the screen. There is no change in meno structure and function.

Symptom:

  1. Teletext in P-a-P gives TV + TV
  2. Intermittent loss of the PUC Table
  3. Standby led is blinking <-----------------
  4. ACM bar opticallt too narrow

Cause

  1. The M2 porcessor was disconnected due to illegal communication. The problem is now fully solved.
  2. The M2 porcessor was disconnected due to illegal communication. The problem is now fully solved.
  3. A powering down problem in the DVF-module. Error not seen on build 433 during test.
  4. When implementing a larger screen, the Auto Color Management bar became a bit too narrow. This does not influence the Automatic Colour Management function.

Solution:

To all above problems, please update to build 433.

Compatibility:

The build is "internally compatible". This means that you must use the entire build when updating the software, do not mix parts of the software with other builds.

 

WE
Offline
Weebyx
Bronze
Posted December 4, 2008 at 05:12 GMT
#1860684
WE
Offline
Weebyx
Bronze
Posted December 4, 2008 at 05:14 GMT
#1860685
T(
Offline
timhanna (archived)
Bronze
Posted December 4, 2008 at 05:22 GMT
#1860686

Guys, I really thank you all for it!

Ah, on the phone again to get this mess sorted!

K(
Offline
KingOfSnake (archived)
Bronze
Posted December 4, 2008 at 07:07 GMT
#1860687
Tim, sorry to offer a non-technical and software related solution, but I have experienced this problem with low voltage lighting and electrical inteference from other IR emitting sources.  Do you have any nearby?
T(
Offline
timhanna (archived)
Bronze
Posted December 4, 2008 at 08:25 GMT
#1860688

Hi KingOfSnake,

Thanks for your response! Well, I do have a cabinet full of: an STB box, PSTN base, router and something else, but not light sources to be honest... :S

Im in the process of arranging a visit by b+o to upgrade the software, under warrenty, mmmaaaaybe it will fix it.

Thanks agian

T(
Offline
timhanna (archived)
Bronze
Posted December 29, 2008 at 04:10 GMT
#1860689

Hope everyone had a great Xmas!

Sorry, for not posting the solution, the answer is to upgrade to SW 5.02, all, working great.

or
BeoWorld Gold Membership card
Join BeoWorld

Register to access the forums, reference material, and exclusive member benefits — including our monthly prize draw.

Become a Member

December 2026 Prize Draw

Gold Members Only

As a Gold member you're automatically entered into our exclusive prize draw — your chance to win iconic Bang & Olufsen products. A unique benefit of BeoWorld Gold membership, every draw brings a new opportunity to win something special.

View Prize Go For Gold