Sign in   |  Join   |  Help

Search

  • Re: Essence MKII vs Core

    The core hardware is faster, but the software is basically the same. Probably no need to factory reset all the devices, but since you mention a phantom product showing in the BeoTool, I would try resetting the list of discovered beolink devices on each device, and maybe start from scratch with the product integration on the two televisions. I'd try removing power from off all the devices, then power on one at a time starting with the televisions. Each time you power on a new device, and before
    Posted to General Discussion & Questions (Forum) by riverstyx on Sun, Nov 24 2019
  • Re: B&O equipments not responding to BEO4/5 remotes, help

    It should be possible to change the BS9000 to A.OPT 1 or 2 without the dummy plug or speakers connected, at least to confirm this is the issue, but it will reset back to A.OPT 0 the next time it is powered off (I can't remember if this happens when the 9000 is switched to standby, or only when power is disconnected and reconnected though).
    Posted to BeoWorld Nordic (Forum) by riverstyx on Sun, Nov 24 2019
  • Re: BL3500 Microcomputer PCB upgrade

    Yes, the v3.33 microprocessor is still available from B&O under the part number in my previous post, and it will work in the earlier BS3500 models (without powerlink socket), but there is no MCL support in this firmware, so the 3500 be ML only from that point onwards - but I'm guessing this is unlikely to be a problem if you're wanting it for N.RADIO/N.MUSIC support. I've mainly installed this module where there was a ML gateway in the setup as 3.33 supports the ML gateway (as well
    Posted to General Discussion & Questions (Forum) by riverstyx on Fri, Sep 27 2019
  • Re: BL3500 Microcomputer PCB upgrade

    [quote user="beojeff"] I asked my dealer a few years ago and he advised that it's no longer available from B&O. [/quote] You dealer is correct that 2.x software / uP module for the earlier BL3500 is no longer available, but you can upgrade these to 3.33 using part number 8002944. This part is intended for the later wireless enabled BL3500 models with powerlink socket and wireless support, but will work fine with the earlier BL3500 models too, you will just lose the ability to use
    Posted to General Discussion & Questions (Forum) by riverstyx on Fri, Sep 27 2019
  • Re: Beosound Shape - what do you think now?

    I'm not sure if you are aware, but there was a recent software update which now allows you to use the core and connect the amplifier via powerlink. If you're playing music through the core, and the powerlink from the BV is activated, then the powerlink takes priority and the music from the core is paused.
    Posted to General Discussion & Questions (Forum) by riverstyx on Sun, Sep 15 2019
  • Re: New Beovision 14-55 - worth buying it?

    What other masterlink products do you have still connected? If it is just link speakers then your issue will be that there is nothing supplying power to the masterlink bus now that you have disconnected the BV10. If this is your issue, there is a power box available from B&O to overcome this. Martin.
    Posted to General Discussion & Questions (Forum) by riverstyx on Sun, Sep 15 2019
  • Re: Beolab 8000 - recloth frets for less than 10GBP

    I just used the tranparent craft stuff which usually has a red backing.
    Posted to The Workbench (Forum) by riverstyx on Sun, Sep 8 2019
  • Re: Control of Beovision 7-40 floor stand

    This extract from the service manual should help with control of the stand - you'll still need to scope the position feedback signal to see how that is encoded though. The manual says: "Pin 4 Stand Position Feedback 0 - 5 V pulses" but doesn't go into any more detail.
    Posted to The Workbench (Forum) by riverstyx on Tue, Aug 20 2019
  • Re: Another Beolink set up question BV11 with BM5, BS9000 and essence in same room

    Hi Toby, Assuming your BS9000 still has the v1.4 software that it shipped from the factory with, it will require an update to support N.MUSIC / N.RADIO - this will require an engineer to swap the software chip but it's a relatively straightforward process. See https://www.beoworld.org/article_view.asp?id=197 for further details. From memory, test mode 23 will give you the software version - so SHIFT 90258 then 23. Note you will need to set it to A.OPT 1 before you can access the test modes. Once
    Posted to General Discussion & Questions (Forum) by riverstyx on Wed, May 1 2019
  • Re: How to adjust electronic curtains on BeoSystem 3

    The document seems to indicate there are cinema off timings as well as cinema on timings. I'm not sure whether the cinema off timings are honoured during startup from standby, or only when you switch back out of format 0 mode but it would be worth trying if you haven't already. Martin.
    Posted to General Discussion & Questions (Forum) by riverstyx on Tue, Apr 30 2019
Page 4 of 93 (929 items) « First ... < Previous 2 3 4 5 6 Next > ... Last » | More Search Options
Beoworld Security Certificate

SSL