Sign in   |  Join   |  Help

Search

  • Re: BV 10 & BS5 & Masterlink

    Booting a Masterlink system should be done in the following sequence: - Power off all devices - Disconnect every Masterlink device from the Masterlink cables - Set al the V.OPT, A.OPT and L.OPT settings - connect every Masterlink device to the Masterlink cables. - Connect the Video Master device (if it exists in this setup) (which is the case here ) to the mains and power it up. - wait about 2 minutes - Connect the Audio Master device to the mains and power it up. - wait about 2 minutes - Connect
    Posted to General Discussion & Questions (Forum) by RaMaBo on Sun, Feb 24 2019
  • Re: BeoVision 7

    Hi, there's an optical SPDIF connector just left of the HDMI socket :) Get a cheap converter from TOSLink to RCA SPDIF and connect it to the BV7 :) Search on amazon or eBay for: 'toslink to rca'
    Posted to General Discussion & Questions (Forum) by RaMaBo on Mon, Feb 18 2019
  • Re: Beolink Wireless - set up

    Hi, yes, this will work fine if the job is done proper and the junction box is not moved after connecting the splice cables.
    Posted to General Discussion & Questions (Forum) by RaMaBo on Fri, Feb 15 2019
  • Re: Beolink Wireless - set up

    Hi, yes to all You can use a junction box or a masterlink multi-plug box. The latter is easier to handle because you just plug the masterlink plugs into one of the six connectors. So no hassle with cutting existing master link cables and put them into the filthy junction box connectors.
    Posted to General Discussion & Questions (Forum) by RaMaBo on Mon, Feb 11 2019
  • Re: BeoLab 3500 IR receiver issue

    Hi, if everything except IR works on you Beolab 3500 you should replace atleast one SMD capacitor on the Display Board. See this post and read the thread :) I had the same problem and it helped very well.
    Posted to The Workbench (Forum) by RaMaBo on Mon, Feb 4 2019
  • Re: Sendersuche Beovision 8-32

    Na ja, ist halt einfacher und bequemer, wenn nur eine Fernbedienung auf'm Tisch liegt Und ja, man kann jeden Receiver nehmen, wenn es einen zugehörigen PUC gibt, geht's natürlich um Längen besser. Die Technisat sind recht gut und lassen sich auch gut in das B&O Universum integrieren. Evtl beim BV 8-32 unter Anschlüsse nachsehen: IR: PUC1 oder 2 auswählen und dann in der Liste nachsehen nach Tec. Digic oder Tec. HD oder Tec. Isio. Dann sind die entsprechenden PUC
    Posted to Deutsche BeoWorld (Forum) by RaMaBo on Thu, Jan 31 2019
  • Re: Beomaster 5500 Intermittent Noise at Certain Volume Levels

    Hi, for Q1: To avoid influence of the Penta's i would check first whether the noise problem still exists or not. This way you could determine the component causing the issue. for Q2: Normally those amplifiers are set to 11mV across the Emitter resistors. This way the heatsinks should stay cool. But replace the trimpots in advance! for Q3: the lithium battery is seated in the metal can between the front plate and the main chassis. In this metal case is the microprocessor. I hope this helps a bit
    Posted to The Workbench (Forum) by RaMaBo on Thu, Jan 31 2019
  • Re: Sendersuche Beovision 8-32

    Hallo, PUC ist die Bezeichnung, die B&O erfunden hat, mit der Fremdgeräte von einem B&O Fernseher mittels IR Sendemodul gesteuert werden können. Für die Technisat Geräte, auch den Technisat Digicorder HD S2 gibt's diese Code Tabellen und diese lassen sich auch gut in den Beovision 8-32 einspielen und verwenden. Dafür benötigt man aber einen B&O Händler, oder selbst die entsperchende Hard- und Software. Beim Digicorder kann man auch sehr gut die interne
    Posted to Deutsche BeoWorld (Forum) by RaMaBo on Wed, Jan 30 2019
  • Re: Recaping Beomaster 1001, 1200,3000, 4000 etc. Austausch aller Elkos und Tantalkos (Recaping)

    Hi, for the two 4000µf in the powersupply section get two 4700µf Caps. for the 160µF use a 220µF. Electrolytic capacitors have a high tolerance in production, often -20% / + 50 %
    Posted to General Discussion & Questions (Forum) by RaMaBo on Mon, Jan 28 2019
  • Re: Beomaster 1001 problem with FM Stereo detection

    Hi, the stereo decoder could be adjusted without a 2-Channel Oscilloscope! There are 2 ways described in the manual: Stepp 11-13 or 14 and 15. The step 14 uses the oscilloscope in the X-Y Mode, this is not a 2 Channel mode instead it uses the normal y -input and the horizontal deflection is controlled by the x-input signal and not via the timebase. The resistor is the (backup) supply for the transistor if the lamp is broken or disconnected it still gets the supply voltage so that the stereo decoder
    Posted to General Discussion & Questions (Forum) by RaMaBo on Mon, Jan 14 2019
Page 9 of 56 (555 items) « First ... < Previous 7 8 9 10 11 Next > ... Last » | More Search Options
Beoworld Security Certificate

SSL