Sign in   |  Join   |  Help

Search

  • Re: Beomedia 1 and loose cable inside

    Hi Ron, to open the case you have to turn it upside down. Then all Torx screws have to be taken out and the turn the case again. Then the lower part and the rear can be pulled out without any problems. The rubberfeet are mounted to the upper part of the case which wraps the lower part. Ralph-Marcus
    Posted to General Discussion & Questions (Forum) by RaMaBo on Thu, Jan 17 2013
  • Beomedia 1 and loose cable inside

    Hello, i bought a Beomedia 1 and it was shipped quiet fast. But unpacking there was some rumble to hear Opening the Case revealed that the power supply board had loosened and felt off the power connector on the mainboard. Seems no big problem but there's also a small cable from the PCI card routed to under the power supply board. This cable with two seperate pins was also loose on the system board near the pins for FIR (5 pin) and the System managemant bus (SMB connector 6 pin). So my question
    Posted to General Discussion & Questions (Forum) by RaMaBo on Thu, Jan 17 2013
    Filed under: Beomeida 1, loses Kabel
  • Re: Length of Masterlink / number of devices in the installation

    Hi Lars, 400m maximum length for all masterlink cables and maximum of 16 links according to the information here on beotech site Link So with your existing and planned equipment everything should be okay. Regards RaMaBo
    Posted to General Discussion & Questions (Forum) by RaMaBo on Fri, Jan 4 2013
  • Re: beocenter 9500 cd issue, c2103 changed....

    33µF was the original value of C2103 but in the old forum Martin (DieBogener) mentioned that he also had success with a blue 47µF. And i had success with a blue 68µF Capacitor ( Original Philips) which i had when i needed a replacement for the C2103 in my Beogram CD6500. The capacitor has to be a blue Philips / Vishay with at least 33µF / 16V but it can be replaced with a bigger one 47µF for example as long as it is the 'famous' Philips type. Bigger values often
    Posted to General Discussion & Questions (Forum) by RaMaBo on Fri, Dec 28 2012
  • Re: Lintronic programmieren

    Servus, es gibt auch den TSOP5700, dies ist dies SMD Variante des TSOP7000. Vielleicht etwas fitzelig zum Löten, geht aber zur Not. Vielleicht kann man den noch auftreiben. Gruß Ralph-Marcus
    Posted to Deutsche BeoWorld (Forum) by RaMaBo on Mon, Sep 17 2012
  • Re: 5 pin DIN

    Hi, if you use a telephone charger (5V) the speakers will always be switched on. The 5V are a signal from the B&O Audio / Video Output to the speakes to switch on (=5V) or to switch off (=0V). The cable you showed is not useful ! Atleast the two wires carrying the audio signal should be shielded. The 5V trigger line doesn't need to be shielded, but it's probably easier to get a cable where all wires are shielded separately than the special B&O cable itself. Ralph-Marcus
    Posted to General Discussion & Questions (Forum) by RaMaBo on Tue, Sep 11 2012
  • Re: Dead Beocenter 9500

    Hi Mikael, as mika said check TR16 and / or C12. The collector of TR16 should be around 0V only for a short while after power on. Then it should rise to nearly 5 Volts. You said that you get 15,5 mV at the collector that's logical a '0'. The RESET line is low-active due to the line above RESET. and a logical '0' is low. so your processor gets a constant reset signal and cann't start working it's propgramm. If you disconnect the reset line as you done before and connect
    Posted to The Workbench (Forum) by RaMaBo on Tue, Sep 4 2012
  • Re: How to transfer Music/LP's from my 5500 system to Computer to create CD's

    Hi David, i don't know where you can obtain this external USB soundcard mentioned before, but there are a few out there. The problem will be the distance! An USB connection may not be longer than 5m ! But you can put an active ( ! ) USB hub in between 2 USB cables of 5m length each. this gives you a missing 5m for the RCA-DIN cable thingie, which might be ok. But you need a wall outlet for the active USB Hub in 5m distance from your computer. Computer<--------------------->Active USB Hub<
    Posted to General Discussion & Questions (Forum) by RaMaBo on Mon, Aug 13 2012
  • Re: Powerlink über CAT.7 - Asymmetrischer Wandler ?

    Hallo Martin, ich würde die Abschirmung des CAT-6a Kabels auf den Schirm des Powerlink Kabels legen, damit der Schirm auf Masse liegt. Alle anderen 8 Kabel kannst Du belegen wie Du willst. Es gab allerdings hier im Forum einmal die Belegung der B&O Adapter, wenn man die nimmt, dann ist man kompatibel für später, ob's jetzt nötig ist oder nicht. Vielleicht hilft der Link schon: Beonet-Handbuch Die RJ-45 Dosen in der Wand sollten natürlich auch abgeschirmt sein und
    Posted to Deutsche BeoWorld (Forum) by RaMaBo on Mon, Jul 16 2012
  • Re: Powerlink über CAT.7 - Asymmetrischer Wandler ?

    Hallo Martin, naja,das was ich schrieb Okay ich meinte mit CAT-7 die RJ-45 Anschlüsse Der Beovision V1 müßte die sysmetrischen Powerlink Anschlüße haben, wogegen die Beosound 9000 noch die guten alten 'normalen', unsymetrischen Anschlüße hat. Also mit Powerlink->RJ45 Adapter auf die Wanddose gehen und am Platz der Lautsprecher an der Wanddose wieder herausgehen zu einem RJ45 -> Powerlink Adapter und an die 'alten', asymetrisch angebundenen
    Posted to Deutsche BeoWorld (Forum) by RaMaBo on Mon, Jul 16 2012
Page 56 of 57 (565 items) « First ... < Previous 53 54 55 56 57 Next > | More Search Options
Beoworld Security Certificate

SSL