Sign in   |  Join   |  Help

Search

  • Re: BEOGRAM 8000 Tonearmcabling

    Thank you very much for your advice and your information of the tonearm contruction. I've already demounted the tonearm, the slider couterweigth and pulled out the thin wires incl. the silicon hose inside the tonearm. Sadly there is no broken cable outside of the tonearm and inside the tonearm as far i can look inside. I can measure the lost connection between the end of one of the wire and the cartridge connector. So I''ve to go the only way and pull the connector out of the tonearm
    Posted to BeoGram (Forum) by Spassmaker on Thu, May 9 2019
  • BEOGRAM 8000 Tonearmcabling

    Hello everyone. I hope to get some Information and advise about the cabling of the Beogram 8000 Tonearmcabling. Following situation is given: No sound on left channel Tried to measure the coils of the MMC but only one coil is ok the other is high resistance about 0.5 MOhm. Measured on the flexboard on the tangential board same measuring. Took another MMC to compare , same measuring. I've dissasembled the tonearm. I've fiddled out the thin wires to the point where they go into the tonearm
    Posted to BeoGram (Forum) by Spassmaker on Tue, May 7 2019
  • Re: Beocenter 9500 smell...

    Hi Tinman Have you found out what the cause of the burned resistor was? Best Regards Christian
    Posted to The Workbench (Forum) by Spassmaker on Mon, Mar 25 2019
  • Re: Beocenter 9500 smell...

    Hi there Maybe this is an sugestion: I've had a bad smelling in a BC 9500 caused by Rersistor R 131 ( 22 Ohm) on the PCB wich is placed in the upper "Bonnet". It is a Resistor wich goes directly from the Rail Voltage (13,8 V) to the Capstan Motor of the Casette Deck. I could not figure out what the resistor made burning but i have taken the Motor apart and relubed it as far as i came to the Bearings. Also I pulled out the capstans cleand and relubed them. The same I 've made with
    Posted to The Workbench (Forum) by Spassmaker on Mon, Mar 18 2019
  • Re: BEOCENTER 2 will not power up

    Hi Graham Thanks for you sugestions. I've already the Service Manual but no clue to figure out what these Error Codes mean. I do not realy know what "MLSL" Status means so I have no Idea where to search for a defektive PCB. In the Socket Unit or in the Master Unit. I think the uP is in the Socket Unit and I have to look there. Best Regards Christian
    Posted to General Discussion & Questions (Forum) by Spassmaker on Mon, Mar 18 2019
  • BEOCENTER 2 will not power up

    Hello everybody. Hope to get some help from you technical specialists I´ve got a Beocenter 2 wich seems to power up normal wit a steady red LED The Door can be opened and closed with the LOAD Button, the Clamper comes out as usual and can be closed wit the LOAD Button. The other Buttons on the Headunit give a response through a flashing LED but nothing happens, no Display, no Sound no spinning of CD. With a Beolink 4 I´ve got access to the Service Manual wich shows following Errors: Maybe
    Posted to General Discussion & Questions (Forum) by Spassmaker on Sat, Mar 16 2019
  • Re: Beosound 9000 Soundsettings and CD Naming not possible

    Problem solved Big Thank to André. He sent me a new Eeprom and another IC. Everything is working fine aggain. Best regards to everybody Christian
    Posted to The Workbench (Forum) by Spassmaker on Wed, Feb 27 2019
  • Re: Beosound 9000 Soundsettings and CD Naming not possible

    Double Post
    Posted to The Workbench (Forum) by Spassmaker on Wed, Feb 27 2019
  • Re: Beosound 9000 Soundsettings and CD Naming not possible

    Hi André Nice to hear from you. Hope you're fine again. As I wrote You aleady the BS 9000 works like charme again. You wrote about the Beo4 ATAPE Instruction but i don't know what You realy mean. When i press ATAPE on tge BEO 4 the Display of the BS shows STREAMING. I have no clue for what I should use the Streaming function. Maybe You can give me an explanation. Best Regards Christian
    Posted to The Workbench (Forum) by Spassmaker on Wed, Feb 27 2019
  • Re: Beosound 9000 Soundsettings and CD Naming not possible

    Hi Beobuddy Did You get my PM? Best regards Christian
    Posted to The Workbench (Forum) by Spassmaker on Tue, Jan 15 2019
Page 3 of 4 (40 items) < Previous 1 2 3 4 Next > | More Search Options
Beoworld Security Certificate

SSL