Sign in   |  Join   |  Help
All Tags » Beovox (RSS)

Browse Forum Posts by Tags

Showing related tags and posts for the General Discussion & Questions forum. See all tags in the site
  • Newbie question - BeoSound 9000 MK2

    Hello everyone! New to the site and world of B&O - just purchased a BeoSound 9000 MK2 with a pair of BeoLab 8000 speakers - everything is working just fine. My questions: -Is it possible to connect the BeoLab 11 Subwoofer to this system? If so, is there a special cable to get it connected? -Read...
    Posted to General Discussion & Questions (Forum) by kirby on Thu, Oct 22 2020
    Filed under: Beovox, beosound 9000, Beolab 11 beolab sub
  • trouble shooting advice CX75

    HI All, I just refoamed a pair of CX75 (only the top drivers) and this was not a bad job at all. But now I tested them and they really sound as a beverage can. I didn't test them beforehand. Now my question where to start with troubleshooting? As I'm quite new to this. Already measured the disconnected...
    Posted to General Discussion & Questions (Forum) by Der_Rudi on Sun, Jun 7 2020
    Filed under: Beovox, CX100
  • Beovox S4500 (6318) vs. S45.2 (6312) - stuck woofer

    Hey, i recently got a pair of Beovox S4500 (6318) speakers, but one of them doesn‘t perform at all in the low end or bass part. I wonder wether or not the woofer is actually the same as in the Beovox S45/S45.2 (6302/6312) as it looks identical to me. How can i make sure that it suffers from the...
    Posted to General Discussion & Questions (Forum) by BertMcMeyer on Sat, Feb 6 2016
    Filed under: Beovox, woofer, Beovox S45, Beovox S45.2, Beovox S4500
  • BEOVOX S45-2 (T6312)

    I acquired a pair of these speakers and want to use them for my living room 2.1 setup. A few questions: Is there anywhere I could find stands for these? Right now I have them on the floor and I know that isn't optimal. Secondly, would the S45-2's work with this audio receiver ? I don't want...
    Posted to General Discussion & Questions (Forum) by sabester24 on Sun, Dec 13 2015
    Filed under: Beovox, S45-2
  • beovox 1702

    Hi everyone, l am a new member so l hope this is a question for the general forum. l purchased a pair of beovox 1702 speakers a few weeks ago and they sound great (l like the detail) however one woofers rubber surround has gone soft so l can only use at lower volumes to prevent over excursion. l have...
    Posted to General Discussion & Questions (Forum) by Beovoxnewbie on Wed, Sep 2 2015
    Filed under: Beovox
  • Gaskets? Would replacing these have any discernible effect on the sound quality?

    Hi, I have a pair of re-foamed CX 100s, but the gaskets around the rear panels and around the Front top and bottom drivers are really quite tired and flat looking. Would replacing the gaskets have any discernible effect on the sound quality? If so are the gaskets available from anywhere, or would it...
    Posted to General Discussion & Questions (Forum) by sxp on Fri, Aug 14 2015
    Filed under: Beovox, Beovox CX-100
  • Beomaster 3000-2 and Beovox 3702 Speakers

    Hi, I have just puchased the above plus the Beogram to match - all very exciting! Anyway I have started the setup and have 2 challenges: 1. I only can get sound out of one speaker and I have tried on both set 1 and set 2 inputs. Its not the speakers as one will work perfectly if I put into "live"...
    Posted to General Discussion & Questions (Forum) by poliver2 on Sun, Jun 21 2015
    Filed under: beogram, Beovox, Beomaster 3000
  • Beovox S80.2 Crossover Help

    Hi, one of my S80.2 recently lost sound out of its mid and low frequency drivers. The issue is with the speaker not the amplifier, and I'm assuming it is with the crossover circuit. However the crossovers were overhauled a few years ago (according to the guy I bought the pair from a year ago). Inspecting...
    Posted to General Discussion & Questions (Forum) by Ky on Wed, Apr 8 2015
    Filed under: Beovox, problem, cross-over, S80.2
  • Conjoined CX50s.. would this work, or does this sound a bit bonkers?

    Hi, I'm new here, and I'd like some advice please.. I have just purchased and restored re-foamed and re-fretted 2x CX50s and 2xCX100s, and I really love em.. I'm thinking about another 2x CX50s laying sidewards tweeter-to-tweeter (bottom-to-bottom) to create a large centre speaker; that way...
    Posted to General Discussion & Questions (Forum) by sxp on Tue, Jul 15 2014
    Filed under: Beovox, BeoVox CX100, BeoVox CX50
  • Which speaker cables for Beovox RL 140's? And why?

    Setup: Beovox RL 140's to Beomaster 3000 I was suggested to use 2-pin DIN cables with both male and female plugs but I don't like the idea of the plugs sticking out from the sides of the speakers. Would the cables with 2-pin DIN male plugs on one end and bare cables on the other end (for the...
    Posted to General Discussion & Questions (Forum) by 4L86 on Mon, Mar 24 2014
    Filed under: Connection, redline, bang olufsen, loudspeakers, Beovox, passive speaker, Beovox RL 140, Beomaster 3000 type 2933
Page 1 of 2 (20 items) 1 2 Next >
Beoworld Security Certificate

SSL