Posts by zoolander (archived2)
13 total posts10 results
Beocord 8002 - Motor spinning without belts? Belts identical with 9000?
in Imported Content (Unmapped) · Dec 30, 2019 13:49[quote user="Dillen"] Yes. Check the fuse holder too. It's known to become weak from oxidation. Martin [/quote] Thank you Martin, you are right. The holder is not as clean as it should be. Not really oxidated yet but the…
Beocord 8002 - Motor spinning without belts? Belts identical with 9000?
in Imported Content (Unmapped) · Dec 30, 2019 13:10Hello again, I checked the 250mA fuse of the deck and it´s blown. Am I right that the buttons as play/ ff/ rw still work without that fuse but not the motor? I will get a new one today to test it. Could be the same probl…
Beocenter 7000 - New belts but doesn't play & where does the connector belong to?
in Imported Content (Unmapped) · Dec 27, 2019 15:16According to Nicks pictures of the mechanism I found, everything seems to be o.k. and shouldn't be the source of error. Take a look for yourself: left side: right side:
Beocenter 7000 - New belts but doesn't play & where does the connector belong to?
in Imported Content (Unmapped) · Dec 26, 2019 20:08[quote user="Dillen"] You don't show much of the tapedeck in question. Does the right reel rotate, when you press play - even only for a brief moment? The lose plug could belong on the turntable section. Tight belts and …
Beocenter 7000 - New belts but doesn't play & where does the connector belong to?
in Imported Content (Unmapped) · Dec 24, 2019 21:58Merry Christmas everyone! As a little Christmas present for myself I wanted to awake the tapedeck of my beocenter 7000 so I granted it some new belts. The old ones were stiff and one of them even ruptured with just a lit…
Beocord 8004: belt climbs on pulley?
in Imported Content (Unmapped) · Dec 23, 2019 20:51Well...I guess we coincidentally have a similar problem. I just bought a 8002 with similar behaviour. I posted it over there in the vintage board: /forum/imported-unmapped/beocord-8002---motor-spinning-without-belts-belt…
Beocord 8004: belt climbs on pulley?
in Imported Content (Unmapped) · Dec 23, 2019 17:16Hi! You don`t need to be an expert at all to take a look at your belts. Just loosen the two screws at the backside and flip open the case. Then there are another three screws needed to be removed, carefully unplug the tw…
Beocord 8002 - Motor spinning without belts? Belts identical with 9000?
in Imported Content (Unmapped) · Dec 19, 2019 22:15Hi Dillen, thanks for your help and sorry for my late response. The last few weeks have been a little turbulent and the beocord was put aside. So the motor normally should spin (some time) even when there are no belts pl…
Beocord 8002 - Motor spinning without belts? Belts identical with 9000?
in Imported Content (Unmapped) · Dec 6, 2019 22:26Hi there! Recently I got a beocord 8002 with some belt replacement needed according to the seller. So I tried with the old ones of my beocord 9000 (that still were doing ok until I replaced them). Well...neither the tape…
Beocenter 7000 - Changing Belts
in Imported Content (Unmapped) · May 31, 2015 16:11Hi there everybody! Just wanted to renew the belts in my beocenter 7000 tapedeck. On first sight that seems to be a pretty quick thing. Just loosen the three screws the mechanism is mounted to the center and then pull it…