Posts by johnpc (archived2)
125 total posts101 results
S45 rubber
in Imported Content (Unmapped) · Mar 6, 2020 19:44I stand corrected, I did not know there were two versions of the S45. You learn something new every day.
S45 rubber
in Imported Content (Unmapped) · Mar 4, 2020 10:47With that type no I think you have S45, someone has replace the foam with rubber. Maybe a bit of "Impact adhesive" is needed where the rubber is parting from the speaker. Also follow the advice above about a bead of Epox…
Beomaster 5500 starts spontaneous
in Imported Content (Unmapped) · Feb 18, 2017 15:41Low energy light bulbs can trigger remote commands up to a minute after being switched on. I have this trouble with my Beocenter 7002. Have you covered the sensor to eliminate external causes? John.
Red line speakers
in General Discussion & Questions · Nov 28, 2016 13:30Thank you Martin, Am I right believing the RL60.2 do not suffer from foam rot ? John.
Red line speakers
in General Discussion & Questions · Nov 28, 2016 11:08I have found a pair of Red Line 60.2 6513 speakers, described as having no ABR, Is this a fault / reason for sale ? or is it how they were made? I need them to go with Beocenter 7000. They are wall mounted but I suppose …
Voltmeter
in Imported Content (Unmapped) · Mar 30, 2016 22:14Original question was Trying to diagnose a non dropping tone arm on a BG4002. I would suspect hardened grease, clean and lubricate, Hopefully no meter required. John.
Veneer transplantation
in Imported Content (Unmapped) · Mar 11, 2016 16:29That is an excellent repair. You were lucky to have a spare piece of wood inside to use. John.
Veneer transplantation
in Imported Content (Unmapped) · Mar 10, 2016 19:26Looks like you have made a good match with the grain if the wood. The camera flash makes any different colours look more than they are. If it did want darkening you could put a dab of darker dye on it. A tip I have learn…
Beocenter 7 segment LED display faults
in Imported Content (Unmapped) · Feb 28, 2016 20:15Plenty of faulty LED displays reported on the forum. How reliable are the actual LED segments? I ask this because 41years since I made an LED clock from "Practical Wireless" that has been in use every day since. Touch wo…
Beocenter 7000 - Changing Belts
in Imported Content (Unmapped) · Jun 11, 2015 17:53I suppose you have repaired it now, but if not. You need to lift both the turntable and radio sections "Remember to remove platter first and protect stylus. You will then be able to pull out the two plugs "Be careful not…
Beocenter 7002 VU indicator fault
in Imported Content (Unmapped) · May 4, 2015 17:56I think I have cured problem with switch cleaner, just hope I have not spoken to soon. Both relays have part no 7600045 relay 6v. Two different relays were fitted, one had markings "Type C2V-2 6volts the other looked vey…
Beomaster 8000 turned itself on
in General Discussion & Questions · May 3, 2015 21:10I have a Beocenter 7002 similar age to your set, my energy saving bulbs send enough interference to switch set on or off. This usually happens < 2 minutes after lights are switched on. Different signals as the bulbs age,…
Beocenter 7002 VU indicator fault
in Imported Content (Unmapped) · May 3, 2015 11:13Hi Martin, Before I open set, can you supply me with two relays? John.
Beocenter 7002 VU indicator fault
in Imported Content (Unmapped) · May 2, 2015 19:31Thank you Martin, Don't these relays respond to cleaning contacts? John.
Beocenter 7002 VU indicator fault
in Imported Content (Unmapped) · May 2, 2015 10:43This BC7002 has been working without fault for 6 weeks. Today I noticed the vu leds were on when playing a record or when using radio, this was intermittent and did not bother me. Then when playing tape fault happened al…
Help needed making perspex Balance slider for Beocenter 4600
in Imported Content (Unmapped) · Apr 27, 2015 16:58Thank You Dave for looking, I think that might be what I had seen. I think I will try to make one to match the other sliders I have. John.
Help needed making perspex Balance slider for Beocenter 4600
in Imported Content (Unmapped) · Apr 27, 2015 16:11Some one on this forum made some sliders for a similar set. Anyone know the article I mean? It may have been made two years since and had lots of pictures. I just need to make a Balance control and the bottom piece from …
Beocenter 4600 small part.
in Imported Content (Unmapped) · Apr 17, 2015 22:27Sorry for the guessing game, but I always have difficulty in sending pictures. I will try tomorrow. John.
Beocenter 4600 small part.
in Imported Content (Unmapped) · Apr 17, 2015 22:16Hi All, I have a BC4600 with the usual stuck buttons, that I removed and cleaned. I also removed the guides to make it easy to clean, I just sprayed IPA into the buttons and worked them on the guides. Then while cleaning…
Beogram 4002 fluctuate at 33 rpm
in BeoGram · Apr 4, 2015 13:46Looking at circuit resistor for setting 33rpm, can not see part number and pre-set resistor 1R15 should be looked at first, then relay 1RL1 contacts. The resistors mentioned above will need a small amount of switch clean…