One IR-Eye for two devices - possible ?

in General Discussion & Questions · Feb 29, 2012 07:56 GMT

IF you have two boxes firing at the same time, no device will recognize the command. You will need to use timer control to have one command beeing fired after the other. hfat

Samsung TV in B&O Umgebung

in Deutsche · Feb 28, 2012 06:46 GMT

Versteh... Hab ne Mail mit den Dateien geschickt hfat

Samsung TV in B&O Umgebung

in Deutsche · Feb 28, 2012 04:37 GMT

Hallo, Der alte Configurator kann auch die Variablen, das sollte kein Problem sein. Welche Command Lists brauchst to genau? Was meinst du mit "Es stört nur das die beiden Geräte über einen den selben Befehl ein und ausge…

How to Guide – Loewe Individual TV set with B&O speakers

in General Discussion & Questions · Feb 26, 2012 14:46 GMT

Hi uysalt, You could use a Lintronc -238 box to control your Loewe with the Beo4. It's already in the lintronic DBB: http://www.lintronic.dk/Support.asp?Supported_ID=1461 hfat

HILFE! BeoSound 5 Encore / N-Music / Festplatte an Modem / NTFS-Partition !!!

in Deutsche · Feb 26, 2012 14:38 GMT

Hallo Lars, Ich habe gerade in der Bedienungsanleitung nachgelesen und gesehen die Standard IP des NAS ist: 169.254.100.100. Damit kannst das NAS mir der von dir angegeben IP 192.168.x.x nicht in deinem Netz finden. Wenn…

HILFE! BeoSound 5 Encore / N-Music / Festplatte an Modem / NTFS-Partition !!!

in Deutsche · Feb 26, 2012 14:06 GMT

Hallo Lars, Die Verbindungen scheinen richtig zu sein, da du über den QNAP Finder das NAS findest. Wichtig ist vorerst, dass die NAS Administration via Browser fiunktioniert. Dann kannst du die nächsten Schritte machen. …

2 Signalquellen an Beolab 4000?

in Deutsche · Feb 25, 2012 10:13 GMT

Hallo, Du drückst auf der Beo4 Standby+List gleichzeitig. Dann erscheint das Setup-Menu der Beo4. Normalerweise steht dann ADD als die erste Funktion im Menu. Drücke sooft List bis Option erscheint. Dann die GO-Taste. Es…

2 Signalquellen an Beolab 4000?

in Deutsche · Feb 25, 2012 02:10 GMT

Hallo, Soweit ich das sehe, ist nur der Anschluss 1 ein Eingang. Anschluss 2 dient der Weiterleitung des Lautsprechersignals an den zweiten Stereolautsprecher. Im Normalfall werden die Lautsprecher nur am BeoVisionproduk…

Beo5 Restore

in Beo5 & Beo6 · Feb 23, 2012 13:29 GMT

The restore function for me works as follows: I choose edit in the setup dialogue, navigate to a button click it. The options show and hide appear. I choose hide and exit the setup dialogue. The button isn't vivible anym…

Beo5 Restore

in Beo5 & Beo6 · Feb 23, 2012 05:21 GMT

Did you change your dealer's configuration with the edit function of the setup dialog before? Did you hide or show buttons before? hfat

Beosound 8 Issues with Beo5

in Beo5 & Beo6 · Feb 21, 2012 09:57 GMT

Hi, I've sent you a PM. hfat

Beo5 Restore

in Beo5 & Beo6 · Feb 21, 2012 03:35 GMT

As far as I remember, the restor function resets the beo5 to the configuration loaded to it. Within the setup dialog you may hide or show buttons in your configuration. Restore simply removes your modifications. hfat

Beosound 8 Issues with Beo5

in Beo5 & Beo6 · Feb 21, 2012 00:52 GMT

what about a feedback? Did it work? hfat

Beosound 8 Issues with Beo5

in Beo5 & Beo6 · Feb 19, 2012 15:44 GMT

After completing this procedure, the beosound 8 should respond to your beo5 You should try now Hfat

Beosound 8 Issues with Beo5

in Beo5 & Beo6 · Feb 19, 2012 14:27 GMT

OK, I just read your latest post. So let's try the following (from the FAQ), asuming you have only a Beo5 at hand and no Beo4. Option programming with Beo5/Beo6: While holding the • button, press the centre button to bri…

Beosound 8 Issues with Beo5

in Beo5 & Beo6 · Feb 19, 2012 14:17 GMT

B&O Products have different options to react when receiving IR signals. These are V.Opt for video products, A.Opt for audio products and L.Opt for link room products. These Options are from 0 to 6. Option programming is …

Beosound 8 Issues with Beo5

in Beo5 & Beo6 · Feb 19, 2012 13:59 GMT

Did you option program your beosound 8? Have a look at the faq section of B&O web site. hfat

Where is the SHIFT command into config tools?

in Beo5 & Beo6 · Feb 19, 2012 09:15 GMT

Although it cannot be selected from the list, you can add it manually by entering SHIFT into to command field and clicking add. hfat

No sound with Appletv2 and beosystem2/BV4

in General Discussion & Questions · Feb 12, 2012 05:26 GMT

Hello, Try using the Link-AV (via List) command on the Beo4 hfat

Lintronic Users - Role Call!

in General Discussion & Questions · Feb 7, 2012 16:35 GMT

Hello, In the main room I use 2 BV10-SCART connected 238-boxes for controlling devices not in the PUC list (XBMC Multimedia PC, Sony BDP). One for controlling BS2/JVC Beamer Combo. All in a hidden installation. In the li…