Posts by tc0fh (archived)
35 total posts27 results
The upgrade of my avant 28" to 50" plasma integrated a mediabox and blu ray player.
in General Discussion & Questions · Mar 17, 2011 17:38I think it shuts down because of the power supply overload signal from the deflection board or the feedback signals to the TDA9162 on the decoder board. Have you seen the text strings in the beosystem software eprom?
The upgrade of my avant 28" to 50" plasma integrated a mediabox and blu ray player.
in General Discussion & Questions · Mar 17, 2011 16:04The idea is to use as much as possible from the original Avant (or BV3) chasis. From some experiments with beosystem 2 (mk 1,2 and 3) I know that the software is clever enough to figure out what's connected and behave ac…
The upgrade of my avant 28" to 50" plasma integrated a mediabox and blu ray player.
in General Discussion & Questions · Mar 17, 2011 15:25Hello! Reviving an old thread... I was thinking along this line: take a Beovision Avant or Beovision 3, get rid of the deflection coil and the rest of the high power stuff, replace the tube with a plasma or LCD, fit some…
BV3_32 AVAND DVB-S kit installed in a Beosystem 2
in General Discussion & Questions · Mar 7, 2011 12:29Hello! I installed a BV3_32 and AVANT DVB-S kit in a Beosystem 2 mk iii type 9422 sw 16.2 and the good news is that it works. The bad news is that the board will not fit properly in the chasis. The really bad news is tha…
Beosystem 2 and DVB-T/S (4463)
in General Discussion & Questions · Mar 7, 2011 12:17Hello! Today I received the DVB-S kit I got on ebay (Sattelite Kit Avant BV3_32 DVB-S 1403200) and I installed it in my Beosystem 2 mk3 type 9422 sw 16.2 The DVB-S works fine. However, the board does not fit properly in …
How to fix the LC2 sensi-touch field
in The Workbench · Sept 17, 2009 10:40Hello! I have LC2 that doesn't respond to the touch function and I decided to fix it. First I tested the sensi-touch field by touching the PCB pad where the small rubber tube fits. It was working. I checked the faulty do…
LC2 service manual
in The Workbench · Sept 7, 2009 07:29Hello! Where can I find the LC2 service manual with a schematic diagram? Is there a list of service manuals available on BeoWolrd? Thanks.
Self learning DVD controller
in The Workbench · Sept 5, 2009 15:05And I just rememberd this: I want to be able to convert from BEO4 to any other IR command and controll other equipment as well (like lights).
Self learning DVD controller
in The Workbench · Sept 5, 2009 15:00Thanks! As I got most of my B&O equipment on ebay, IR relay for BeoMedia is a must as I only have one IR Eye (for the moment). The good bit about converting the STB-C codes is that you can pick any box on the list that l…
Self learning DVD controller
in The Workbench · Sept 5, 2009 13:42Hello! I decode long left/right/up/down stop/go and green/yellow/red/blue codes. BTW, the long go is the same as long stop 🙂 You're right, there's no need to relay IR to BeoPort. But I might need to relay to BeoMedia 1 …
Self learning DVD controller
in The Workbench · Sept 5, 2009 11:02Hello! I started working on a compatible DVD Controller. So far I can decode all the data on PIN8 of the AV and V.TAPE on my beosystem 2. The beosystem 2 sends about 50 commands that have a prefix of the source (DVD, V.M…
Needed B&O Miocrocomputer uPH8
in General Discussion & Questions · Sept 5, 2009 10:45I have fixed the board. The ST24C02 serial eeprom (the one with the PIN security system) was corrupted and I managed to rebuild the information in it. I think that mains power failed at exactly the same time as the CPU w…
Firmware changelog for Beosound 3000 and Beosystem 2
in General Discussion & Questions · Jul 12, 2009 10:26Hello! Can someone tell me what has changed in the firmware for Beosound 3000 from version 3.1 to version 3.4 (which I think is the latest) and for Beosystem 2 mk 1 from version 1.4 to version 1.6? Did the V.TAPE and A.T…
Needed B&O Miocrocomputer uPH8
in General Discussion & Questions · May 15, 2009 11:23Hello again! My dealer forwarded a reply from BeoCare that says you cannot get that module, just the whole chasis. Can anyone confirm the price for 8006797? My dealer quoted me for over 600 Euro. Regards, Andrei
B&O Programmer
in General Discussion & Questions · May 14, 2009 08:34Hello! Can you send me the manual, please? Regards. Andrei
Needed B&O Miocrocomputer uPH8
in General Discussion & Questions · May 14, 2009 07:34Hello! Can I send you the defective part and have it serviced in your service center? Regards, Andrei
Needed B&O Miocrocomputer uPH8
in General Discussion & Questions · May 13, 2009 13:39Hello! It is the one from the Beosystem 2 I bought on e-bay and that didn't work (almost) at all. /forum/general-discussion-and-questions/beovision-5-switch-off-every-day-at-the-same-time I used the PCB from my Beosound …
Needed B&O Miocrocomputer uPH8
in General Discussion & Questions · May 13, 2009 11:10Hello! I need a functional uPH8 microcomputer printed circuit board (PCB) from a Beosound 3000 or a Beosystem 2 or a Beovison Avant or Beovision 5 or any other B&O device that uses this processor board. This board is cal…
B&O Programmer
in General Discussion & Questions · May 6, 2009 15:18Hello What can I do with an B&O Programmer? Is there a manual for it somewhere? Regards, Andrei
Beosystem 1 - IR Receiver
in North America · May 4, 2009 15:51Hello! I managed to hook an IR eye from a beolink active to the BeoLink PC2. Check my other posts. I was wondering if you are willing to test the connection in my post on your Beosystem. I tried to use the same IR eye wi…