Posts by Hank (archived)
29 total posts24 results
Beosound 9000 Shut Down?
in General Discussion & Questions · Mar 19, 2010 15:48After the reboot of the system it´s even worse. Now the standby led goes on and off, when the standby led is off all the led´s over the CDs are on. it´s flashing all the time. Anyone who knows what it could be? Seems lik…
Beosound 9000 Shut Down?
in General Discussion & Questions · Mar 19, 2010 07:19I think it´s a MK2 edition and it doesn´t use PIN code. Yes the power was cut in the whole house for 6 hours. I talked to B&O service today and they told me to disconnect all units and leave it for 2 hours and then start…
Beosound 9000 Shut Down?
in General Discussion & Questions · Mar 19, 2010 05:25I need some help with my Beosound 9000 which shut down by it self after 3 seconds. If you start the stereo by AUX, CD or Radio it will start and after 3 seconds go back to standby mode without any info. I have no clue ab…
Need help with noise in my speakers
in General Discussion & Questions · Mar 18, 2009 15:16I have now connected the speakers to the computer through a PL to RCA cable. With this connections the speakers sounds like them should. Next step is now to modify the PL cable and try again. If it doesn´t work it must b…
Need help with noise in my speakers
in General Discussion & Questions · Mar 18, 2009 10:40I don´t get this problems with my Beolab 4000, but it might be Beosound 9000 that cause this noise.
Need help with noise in my speakers
in General Discussion & Questions · Mar 17, 2009 11:00Thanks "Liberal" for your suggestion. I will try to modify the cable and test it. I have to find a good way to cut the wire to pin 7 and shortcut between pin 2 and pin 7. Can I do this shortcut in the contact? "KingofSna…
Need help with noise in my speakers
in General Discussion & Questions · Mar 16, 2009 02:51Hello I have a problem with my BS9000 and a pair of beolab 3. When the power is switched on the speakers there is an annoying high pitched humming noise that I can't solve. The noise is present all the time even when the…
detoma loudspeakers
in General Discussion & Questions · Feb 27, 2009 09:45Yes, I had a couple of Stavolo 400 Active but I sold them because they didn´t sound good enough. They were not as good as BL4000. But I use Detoma D90 active in my bathroom because they are not so big as B&O´s inwall spe…
BS9000/Lab 3's humming noise problem.
in General Discussion & Questions · Feb 24, 2009 07:00I have the same problems with my Beosound 9000 and BL3´s. I use two different cables to them: 1 P.L Mk1 which gives a noise tone like a radio without any station at the frequenze. 1 P.L MK3 Bossocom with this cable you g…
Connecting beolab 4000s to a plasma for TV sound
in The Workbench · Feb 24, 2009 06:42I use a pair of Beolab 4 connected directly to my Plasma via speakers out. But it´s important that you have a speakers out from the TV, beacuse if you use line out you can´t control the volume. It might be possible to us…
Installation of new tweeter for beolab 3
in General Discussion & Questions · Feb 20, 2009 07:17That is a great suggestion. Do you have to mount the slave bas unit when you listning or can I keep it open? I recieved a mail from B&O support and they say that +0.04 can be correct.
Installation of new tweeter for beolab 3
in General Discussion & Questions · Feb 20, 2009 04:25Yes I understand that this modification is made by own risk. I´m not sure that +0,04 is the correct value beacuse I´m not sure if they measure them so exactly.
Beolab 4. What do you guys think?
in Nordic · Feb 19, 2009 10:00I use a pair of BL4 as speakers to my TV and think they do a quite good work. But as speakers for a stereo, I think they are to weak. I have BL4, BL3 and BL 4000 and think BL3 is the most functional speakers for the mone…
Installation of new tweeter for beolab 3
in General Discussion & Questions · Feb 19, 2009 09:33The tweeter is now longer not what it used to be :-). But it´s good to know that I can change it if I don´t like the sound without crash the speaker again. The problem is that the stickers is hand writen and hard to read…
Installation of new tweeter for beolab 3
in General Discussion & Questions · Feb 19, 2009 08:26Thank you for the answers. I tought that the value supposed to be stated only with one decimal therefor +0,04 wasn´t a option for me. But it might be right if they measure them so exactly. What was the value of your twee…
Installation of new tweeter for beolab 3
in General Discussion & Questions · Feb 19, 2009 06:59I bought a new tweeter for my Beolab 3, and when you change tweeter you also have to change one of the potensiometers on the mainboard to get the correct sound. I found a small note on the speakers back saying (.04) but …
Icepower?
in Nordic · Sept 8, 2008 12:54Någon som vet vad den Icepower module som sitter i Beolab 3 orna heter (250W)? Vad är namnet på den modul som sitter i Lab2 an (850W)? MVH Hank
Högtalare till BeoSound3000
in Nordic · Apr 15, 2008 02:30Hej Kolla vad Peter Pan skriver på sitt "Topic" om att koppla ihop icke B&O sub till B&O system. Där hittar du exakt hur du skall löda och koppla för att det skall bli rätt. Finns under Scandinavien fliken.
New intelligent lightdimmer for B&O remotes
in Nordic · Apr 15, 2008 02:18Någon som vet om RAone SmartDimmer fungerar tillsammans med Plasma TV, vilket LC2an inte gör.
Koppla Beolab 8000 till "vanlig" stereo (icke-B&O-stereo)?
in Nordic · Apr 15, 2008 02:15Som sagt Line-in ingången på högtalarna skall kopplas till Line-Out på TV/CD/STEREO. Om du har Line-Out på din stereo kan du koppla dem dit, men då går det inte att höja volumen. Därför skall du köra med en Pre-out först…